1// SPDX-License-Identifier: GPL-2.0
2/*
3 * BCM2835 master mode driver
4 */
5
6#include <linux/clk.h>
7#include <linux/clkdev.h>
8#include <linux/clk-provider.h>
9#include <linux/completion.h>
10#include <linux/err.h>
11#include <linux/i2c.h>
12#include <linux/interrupt.h>
13#include <linux/io.h>
14#include <linux/module.h>
15#include <linux/of.h>
16#include <linux/platform_device.h>
17#include <linux/slab.h>
18
19#define BCM2835_I2C_C 0x0
20#define BCM2835_I2C_S 0x4
21#define BCM2835_I2C_DLEN 0x8
22#define BCM2835_I2C_A 0xc
23#define BCM2835_I2C_FIFO 0x10
24#define BCM2835_I2C_DIV 0x14
25#define BCM2835_I2C_DEL 0x18
26/*
27 * 16-bit field for the number of SCL cycles to wait after rising SCL
28 * before deciding the slave is not responding. 0 disables the
29 * timeout detection.
30 */
31#define BCM2835_I2C_CLKT 0x1c
32
33#define BCM2835_I2C_C_READ BIT(0)
34#define BCM2835_I2C_C_CLEAR BIT(4) /* bits 4 and 5 both clear */
35#define BCM2835_I2C_C_ST BIT(7)
36#define BCM2835_I2C_C_INTD BIT(8)
37#define BCM2835_I2C_C_INTT BIT(9)
38#define BCM2835_I2C_C_INTR BIT(10)
39#define BCM2835_I2C_C_I2CEN BIT(15)
40
41#define BCM2835_I2C_S_TA BIT(0)
42#define BCM2835_I2C_S_DONE BIT(1)
43#define BCM2835_I2C_S_TXW BIT(2)
44#define BCM2835_I2C_S_RXR BIT(3)
45#define BCM2835_I2C_S_TXD BIT(4)
46#define BCM2835_I2C_S_RXD BIT(5)
47#define BCM2835_I2C_S_TXE BIT(6)
48#define BCM2835_I2C_S_RXF BIT(7)
49#define BCM2835_I2C_S_ERR BIT(8)
50#define BCM2835_I2C_S_CLKT BIT(9)
51#define BCM2835_I2C_S_LEN BIT(10) /* Fake bit for SW error reporting */
52
53#define BCM2835_I2C_FEDL_SHIFT 16
54#define BCM2835_I2C_REDL_SHIFT 0
55
56#define BCM2835_I2C_CDIV_MIN 0x0002
57#define BCM2835_I2C_CDIV_MAX 0xFFFE
58
59struct bcm2835_i2c_dev {
60 struct device *dev;
61 void __iomem *regs;
62 int irq;
63 struct i2c_adapter adapter;
64 struct completion completion;
65 struct i2c_msg *curr_msg;
66 struct clk *bus_clk;
67 int num_msgs;
68 u32 msg_err;
69 u8 *msg_buf;
70 size_t msg_buf_remaining;
71};
72
73static inline void bcm2835_i2c_writel(struct bcm2835_i2c_dev *i2c_dev,
74 u32 reg, u32 val)
75{
76 writel(val, addr: i2c_dev->regs + reg);
77}
78
79static inline u32 bcm2835_i2c_readl(struct bcm2835_i2c_dev *i2c_dev, u32 reg)
80{
81 return readl(addr: i2c_dev->regs + reg);
82}
83
84#define to_clk_bcm2835_i2c(_hw) container_of(_hw, struct clk_bcm2835_i2c, hw)
85struct clk_bcm2835_i2c {
86 struct clk_hw hw;
87 struct bcm2835_i2c_dev *i2c_dev;
88};
89
90static int clk_bcm2835_i2c_calc_divider(unsigned long rate,
91 unsigned long parent_rate)
92{
93 u32 divider = DIV_ROUND_UP(parent_rate, rate);
94
95 /*
96 * Per the datasheet, the register is always interpreted as an even
97 * number, by rounding down. In other words, the LSB is ignored. So,
98 * if the LSB is set, increment the divider to avoid any issue.
99 */
100 if (divider & 1)
101 divider++;
102 if ((divider < BCM2835_I2C_CDIV_MIN) ||
103 (divider > BCM2835_I2C_CDIV_MAX))
104 return -EINVAL;
105
106 return divider;
107}
108
109static int clk_bcm2835_i2c_set_rate(struct clk_hw *hw, unsigned long rate,
110 unsigned long parent_rate)
111{
112 struct clk_bcm2835_i2c *div = to_clk_bcm2835_i2c(hw);
113 u32 redl, fedl;
114 u32 divider = clk_bcm2835_i2c_calc_divider(rate, parent_rate);
115
116 if (divider == -EINVAL)
117 return -EINVAL;
118
119 bcm2835_i2c_writel(i2c_dev: div->i2c_dev, BCM2835_I2C_DIV, val: divider);
120
121 /*
122 * Number of core clocks to wait after falling edge before
123 * outputting the next data bit. Note that both FEDL and REDL
124 * can't be greater than CDIV/2.
125 */
126 fedl = max(divider / 16, 1u);
127
128 /*
129 * Number of core clocks to wait after rising edge before
130 * sampling the next incoming data bit.
131 */
132 redl = max(divider / 4, 1u);
133
134 bcm2835_i2c_writel(i2c_dev: div->i2c_dev, BCM2835_I2C_DEL,
135 val: (fedl << BCM2835_I2C_FEDL_SHIFT) |
136 (redl << BCM2835_I2C_REDL_SHIFT));
137 return 0;
138}
139
140static long clk_bcm2835_i2c_round_rate(struct clk_hw *hw, unsigned long rate,
141 unsigned long *parent_rate)
142{
143 u32 divider = clk_bcm2835_i2c_calc_divider(rate, parent_rate: *parent_rate);
144
145 return DIV_ROUND_UP(*parent_rate, divider);
146}
147
148static unsigned long clk_bcm2835_i2c_recalc_rate(struct clk_hw *hw,
149 unsigned long parent_rate)
150{
151 struct clk_bcm2835_i2c *div = to_clk_bcm2835_i2c(hw);
152 u32 divider = bcm2835_i2c_readl(i2c_dev: div->i2c_dev, BCM2835_I2C_DIV);
153
154 return DIV_ROUND_UP(parent_rate, divider);
155}
156
157static const struct clk_ops clk_bcm2835_i2c_ops = {
158 .set_rate = clk_bcm2835_i2c_set_rate,
159 .round_rate = clk_bcm2835_i2c_round_rate,
160 .recalc_rate = clk_bcm2835_i2c_recalc_rate,
161};
162
163static struct clk *bcm2835_i2c_register_div(struct device *dev,
164 struct clk *mclk,
165 struct bcm2835_i2c_dev *i2c_dev)
166{
167 struct clk_init_data init;
168 struct clk_bcm2835_i2c *priv;
169 char name[32];
170 const char *mclk_name;
171
172 snprintf(buf: name, size: sizeof(name), fmt: "%s_div", dev_name(dev));
173
174 mclk_name = __clk_get_name(clk: mclk);
175
176 init.ops = &clk_bcm2835_i2c_ops;
177 init.name = name;
178 init.parent_names = (const char* []) { mclk_name };
179 init.num_parents = 1;
180 init.flags = 0;
181
182 priv = devm_kzalloc(dev, size: sizeof(struct clk_bcm2835_i2c), GFP_KERNEL);
183 if (priv == NULL)
184 return ERR_PTR(error: -ENOMEM);
185
186 priv->hw.init = &init;
187 priv->i2c_dev = i2c_dev;
188
189 clk_hw_register_clkdev(&priv->hw, "div", dev_name(dev));
190 return devm_clk_register(dev, hw: &priv->hw);
191}
192
193static void bcm2835_fill_txfifo(struct bcm2835_i2c_dev *i2c_dev)
194{
195 u32 val;
196
197 while (i2c_dev->msg_buf_remaining) {
198 val = bcm2835_i2c_readl(i2c_dev, BCM2835_I2C_S);
199 if (!(val & BCM2835_I2C_S_TXD))
200 break;
201 bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_FIFO,
202 val: *i2c_dev->msg_buf);
203 i2c_dev->msg_buf++;
204 i2c_dev->msg_buf_remaining--;
205 }
206}
207
208static void bcm2835_drain_rxfifo(struct bcm2835_i2c_dev *i2c_dev)
209{
210 u32 val;
211
212 while (i2c_dev->msg_buf_remaining) {
213 val = bcm2835_i2c_readl(i2c_dev, BCM2835_I2C_S);
214 if (!(val & BCM2835_I2C_S_RXD))
215 break;
216 *i2c_dev->msg_buf = bcm2835_i2c_readl(i2c_dev,
217 BCM2835_I2C_FIFO);
218 i2c_dev->msg_buf++;
219 i2c_dev->msg_buf_remaining--;
220 }
221}
222
223/*
224 * Repeated Start Condition (Sr)
225 * The BCM2835 ARM Peripherals datasheet mentions a way to trigger a Sr when it
226 * talks about reading from a slave with 10 bit address. This is achieved by
227 * issuing a write, poll the I2CS.TA flag and wait for it to be set, and then
228 * issue a read.
229 * A comment in https://github.com/raspberrypi/linux/issues/254 shows how the
230 * firmware actually does it using polling and says that it's a workaround for
231 * a problem in the state machine.
232 * It turns out that it is possible to use the TXW interrupt to know when the
233 * transfer is active, provided the FIFO has not been prefilled.
234 */
235
236static void bcm2835_i2c_start_transfer(struct bcm2835_i2c_dev *i2c_dev)
237{
238 u32 c = BCM2835_I2C_C_ST | BCM2835_I2C_C_I2CEN;
239 struct i2c_msg *msg = i2c_dev->curr_msg;
240 bool last_msg = (i2c_dev->num_msgs == 1);
241
242 if (!i2c_dev->num_msgs)
243 return;
244
245 i2c_dev->num_msgs--;
246 i2c_dev->msg_buf = msg->buf;
247 i2c_dev->msg_buf_remaining = msg->len;
248
249 if (msg->flags & I2C_M_RD)
250 c |= BCM2835_I2C_C_READ | BCM2835_I2C_C_INTR;
251 else
252 c |= BCM2835_I2C_C_INTT;
253
254 if (last_msg)
255 c |= BCM2835_I2C_C_INTD;
256
257 bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_A, val: msg->addr);
258 bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_DLEN, val: msg->len);
259 bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, val: c);
260}
261
262static void bcm2835_i2c_finish_transfer(struct bcm2835_i2c_dev *i2c_dev)
263{
264 i2c_dev->curr_msg = NULL;
265 i2c_dev->num_msgs = 0;
266
267 i2c_dev->msg_buf = NULL;
268 i2c_dev->msg_buf_remaining = 0;
269}
270
271/*
272 * Note about I2C_C_CLEAR on error:
273 * The I2C_C_CLEAR on errors will take some time to resolve -- if you were in
274 * non-idle state and I2C_C_READ, it sets an abort_rx flag and runs through
275 * the state machine to send a NACK and a STOP. Since we're setting CLEAR
276 * without I2CEN, that NACK will be hanging around queued up for next time
277 * we start the engine.
278 */
279
280static irqreturn_t bcm2835_i2c_isr(int this_irq, void *data)
281{
282 struct bcm2835_i2c_dev *i2c_dev = data;
283 u32 val, err;
284
285 val = bcm2835_i2c_readl(i2c_dev, BCM2835_I2C_S);
286
287 err = val & (BCM2835_I2C_S_CLKT | BCM2835_I2C_S_ERR);
288 if (err) {
289 i2c_dev->msg_err = err;
290 goto complete;
291 }
292
293 if (val & BCM2835_I2C_S_DONE) {
294 if (!i2c_dev->curr_msg) {
295 dev_err(i2c_dev->dev, "Got unexpected interrupt (from firmware?)\n");
296 } else if (i2c_dev->curr_msg->flags & I2C_M_RD) {
297 bcm2835_drain_rxfifo(i2c_dev);
298 val = bcm2835_i2c_readl(i2c_dev, BCM2835_I2C_S);
299 }
300
301 if ((val & BCM2835_I2C_S_RXD) || i2c_dev->msg_buf_remaining)
302 i2c_dev->msg_err = BCM2835_I2C_S_LEN;
303 else
304 i2c_dev->msg_err = 0;
305 goto complete;
306 }
307
308 if (val & BCM2835_I2C_S_TXW) {
309 if (!i2c_dev->msg_buf_remaining) {
310 i2c_dev->msg_err = val | BCM2835_I2C_S_LEN;
311 goto complete;
312 }
313
314 bcm2835_fill_txfifo(i2c_dev);
315
316 if (i2c_dev->num_msgs && !i2c_dev->msg_buf_remaining) {
317 i2c_dev->curr_msg++;
318 bcm2835_i2c_start_transfer(i2c_dev);
319 }
320
321 return IRQ_HANDLED;
322 }
323
324 if (val & BCM2835_I2C_S_RXR) {
325 if (!i2c_dev->msg_buf_remaining) {
326 i2c_dev->msg_err = val | BCM2835_I2C_S_LEN;
327 goto complete;
328 }
329
330 bcm2835_drain_rxfifo(i2c_dev);
331 return IRQ_HANDLED;
332 }
333
334 return IRQ_NONE;
335
336complete:
337 bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, BCM2835_I2C_C_CLEAR);
338 bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_S, BCM2835_I2C_S_CLKT |
339 BCM2835_I2C_S_ERR | BCM2835_I2C_S_DONE);
340 complete(&i2c_dev->completion);
341
342 return IRQ_HANDLED;
343}
344
345static int bcm2835_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[],
346 int num)
347{
348 struct bcm2835_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
349 unsigned long time_left;
350 int i;
351
352 for (i = 0; i < (num - 1); i++)
353 if (msgs[i].flags & I2C_M_RD) {
354 dev_warn_once(i2c_dev->dev,
355 "only one read message supported, has to be last\n");
356 return -EOPNOTSUPP;
357 }
358
359 i2c_dev->curr_msg = msgs;
360 i2c_dev->num_msgs = num;
361 reinit_completion(x: &i2c_dev->completion);
362
363 bcm2835_i2c_start_transfer(i2c_dev);
364
365 time_left = wait_for_completion_timeout(x: &i2c_dev->completion,
366 timeout: adap->timeout);
367
368 bcm2835_i2c_finish_transfer(i2c_dev);
369
370 if (!time_left) {
371 bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C,
372 BCM2835_I2C_C_CLEAR);
373 dev_err(i2c_dev->dev, "i2c transfer timed out\n");
374 return -ETIMEDOUT;
375 }
376
377 if (!i2c_dev->msg_err)
378 return num;
379
380 dev_dbg(i2c_dev->dev, "i2c transfer failed: %x\n", i2c_dev->msg_err);
381
382 if (i2c_dev->msg_err & BCM2835_I2C_S_ERR)
383 return -EREMOTEIO;
384
385 return -EIO;
386}
387
388static u32 bcm2835_i2c_func(struct i2c_adapter *adap)
389{
390 return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
391}
392
393static const struct i2c_algorithm bcm2835_i2c_algo = {
394 .master_xfer = bcm2835_i2c_xfer,
395 .functionality = bcm2835_i2c_func,
396};
397
398/*
399 * The BCM2835 was reported to have problems with clock stretching:
400 * https://www.advamation.com/knowhow/raspberrypi/rpi-i2c-bug.html
401 * https://www.raspberrypi.org/forums/viewtopic.php?p=146272
402 */
403static const struct i2c_adapter_quirks bcm2835_i2c_quirks = {
404 .flags = I2C_AQ_NO_CLK_STRETCH,
405};
406
407static int bcm2835_i2c_probe(struct platform_device *pdev)
408{
409 struct bcm2835_i2c_dev *i2c_dev;
410 int ret;
411 struct i2c_adapter *adap;
412 struct clk *mclk;
413 u32 bus_clk_rate;
414
415 i2c_dev = devm_kzalloc(dev: &pdev->dev, size: sizeof(*i2c_dev), GFP_KERNEL);
416 if (!i2c_dev)
417 return -ENOMEM;
418 platform_set_drvdata(pdev, data: i2c_dev);
419 i2c_dev->dev = &pdev->dev;
420 init_completion(x: &i2c_dev->completion);
421
422 i2c_dev->regs = devm_platform_get_and_ioremap_resource(pdev, index: 0, NULL);
423 if (IS_ERR(ptr: i2c_dev->regs))
424 return PTR_ERR(ptr: i2c_dev->regs);
425
426 mclk = devm_clk_get(dev: &pdev->dev, NULL);
427 if (IS_ERR(ptr: mclk))
428 return dev_err_probe(dev: &pdev->dev, err: PTR_ERR(ptr: mclk),
429 fmt: "Could not get clock\n");
430
431 i2c_dev->bus_clk = bcm2835_i2c_register_div(dev: &pdev->dev, mclk, i2c_dev);
432
433 if (IS_ERR(ptr: i2c_dev->bus_clk))
434 return dev_err_probe(dev: &pdev->dev, err: PTR_ERR(ptr: i2c_dev->bus_clk),
435 fmt: "Could not register clock\n");
436
437 ret = of_property_read_u32(np: pdev->dev.of_node, propname: "clock-frequency",
438 out_value: &bus_clk_rate);
439 if (ret < 0) {
440 dev_warn(&pdev->dev,
441 "Could not read clock-frequency property\n");
442 bus_clk_rate = I2C_MAX_STANDARD_MODE_FREQ;
443 }
444
445 ret = clk_set_rate_exclusive(clk: i2c_dev->bus_clk, rate: bus_clk_rate);
446 if (ret < 0)
447 return dev_err_probe(dev: &pdev->dev, err: ret,
448 fmt: "Could not set clock frequency\n");
449
450 ret = clk_prepare_enable(clk: i2c_dev->bus_clk);
451 if (ret) {
452 dev_err(&pdev->dev, "Couldn't prepare clock");
453 goto err_put_exclusive_rate;
454 }
455
456 i2c_dev->irq = platform_get_irq(pdev, 0);
457 if (i2c_dev->irq < 0) {
458 ret = i2c_dev->irq;
459 goto err_disable_unprepare_clk;
460 }
461
462 ret = request_irq(irq: i2c_dev->irq, handler: bcm2835_i2c_isr, IRQF_SHARED,
463 name: dev_name(dev: &pdev->dev), dev: i2c_dev);
464 if (ret) {
465 dev_err(&pdev->dev, "Could not request IRQ\n");
466 goto err_disable_unprepare_clk;
467 }
468
469 adap = &i2c_dev->adapter;
470 i2c_set_adapdata(adap, data: i2c_dev);
471 adap->owner = THIS_MODULE;
472 adap->class = I2C_CLASS_DEPRECATED;
473 snprintf(buf: adap->name, size: sizeof(adap->name), fmt: "bcm2835 (%s)",
474 of_node_full_name(np: pdev->dev.of_node));
475 adap->algo = &bcm2835_i2c_algo;
476 adap->dev.parent = &pdev->dev;
477 adap->dev.of_node = pdev->dev.of_node;
478 adap->quirks = of_device_get_match_data(dev: &pdev->dev);
479
480 /*
481 * Disable the hardware clock stretching timeout. SMBUS
482 * specifies a limit for how long the device can stretch the
483 * clock, but core I2C doesn't.
484 */
485 bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_CLKT, val: 0);
486 bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, val: 0);
487
488 ret = i2c_add_adapter(adap);
489 if (ret)
490 goto err_free_irq;
491
492 return 0;
493
494err_free_irq:
495 free_irq(i2c_dev->irq, i2c_dev);
496err_disable_unprepare_clk:
497 clk_disable_unprepare(clk: i2c_dev->bus_clk);
498err_put_exclusive_rate:
499 clk_rate_exclusive_put(clk: i2c_dev->bus_clk);
500
501 return ret;
502}
503
504static void bcm2835_i2c_remove(struct platform_device *pdev)
505{
506 struct bcm2835_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
507
508 clk_rate_exclusive_put(clk: i2c_dev->bus_clk);
509 clk_disable_unprepare(clk: i2c_dev->bus_clk);
510
511 free_irq(i2c_dev->irq, i2c_dev);
512 i2c_del_adapter(adap: &i2c_dev->adapter);
513}
514
515static const struct of_device_id bcm2835_i2c_of_match[] = {
516 { .compatible = "brcm,bcm2711-i2c" },
517 { .compatible = "brcm,bcm2835-i2c", .data = &bcm2835_i2c_quirks },
518 {},
519};
520MODULE_DEVICE_TABLE(of, bcm2835_i2c_of_match);
521
522static struct platform_driver bcm2835_i2c_driver = {
523 .probe = bcm2835_i2c_probe,
524 .remove_new = bcm2835_i2c_remove,
525 .driver = {
526 .name = "i2c-bcm2835",
527 .of_match_table = bcm2835_i2c_of_match,
528 },
529};
530module_platform_driver(bcm2835_i2c_driver);
531
532MODULE_AUTHOR("Stephen Warren <swarren@wwwdotorg.org>");
533MODULE_DESCRIPTION("BCM2835 I2C bus adapter");
534MODULE_LICENSE("GPL v2");
535MODULE_ALIAS("platform:i2c-bcm2835");
536

source code of linux/drivers/i2c/busses/i2c-bcm2835.c