1/* SPDX-License-Identifier: GPL-2.0-or-later */
2/*
3 * Device driver for the SYMBIOS/LSILOGIC 53C8XX and 53C1010 family
4 * of PCI-SCSI IO processors.
5 *
6 * Copyright (C) 1999-2001 Gerard Roudier <groudier@free.fr>
7 *
8 * This driver is derived from the Linux sym53c8xx driver.
9 * Copyright (C) 1998-2000 Gerard Roudier
10 *
11 * The sym53c8xx driver is derived from the ncr53c8xx driver that had been
12 * a port of the FreeBSD ncr driver to Linux-1.2.13.
13 *
14 * The original ncr driver has been written for 386bsd and FreeBSD by
15 * Wolfgang Stanglmeier <wolf@cologne.de>
16 * Stefan Esser <se@mi.Uni-Koeln.de>
17 * Copyright (C) 1994 Wolfgang Stanglmeier
18 *
19 * Other major contributions:
20 *
21 * NVRAM detection and reading.
22 * Copyright (C) 1997 Richard Waltham <dormouse@farsrobt.demon.co.uk>
23 *
24 *-----------------------------------------------------------------------------
25 */
26
27#ifndef SYM53C8XX_H
28#define SYM53C8XX_H
29
30
31/*
32 * DMA addressing mode.
33 *
34 * 0 : 32 bit addressing for all chips.
35 * 1 : 40 bit addressing when supported by chip.
36 * 2 : 64 bit addressing when supported by chip,
37 * limited to 16 segments of 4 GB -> 64 GB max.
38 */
39#define SYM_CONF_DMA_ADDRESSING_MODE CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE
40
41/*
42 * NVRAM support.
43 */
44#if 1
45#define SYM_CONF_NVRAM_SUPPORT (1)
46#endif
47
48/*
49 * These options are not tunable from 'make config'
50 */
51#if 1
52#define SYM_LINUX_PROC_INFO_SUPPORT
53#define SYM_LINUX_USER_COMMAND_SUPPORT
54#define SYM_LINUX_USER_INFO_SUPPORT
55#define SYM_LINUX_DEBUG_CONTROL_SUPPORT
56#endif
57
58/*
59 * Also handle old NCR chips if not (0).
60 */
61#define SYM_CONF_GENERIC_SUPPORT (1)
62
63/*
64 * Allow tags from 2 to 256, default 8
65 */
66#ifndef CONFIG_SCSI_SYM53C8XX_MAX_TAGS
67#define CONFIG_SCSI_SYM53C8XX_MAX_TAGS (8)
68#endif
69
70#if CONFIG_SCSI_SYM53C8XX_MAX_TAGS < 2
71#define SYM_CONF_MAX_TAG (2)
72#elif CONFIG_SCSI_SYM53C8XX_MAX_TAGS > 256
73#define SYM_CONF_MAX_TAG (256)
74#else
75#define SYM_CONF_MAX_TAG CONFIG_SCSI_SYM53C8XX_MAX_TAGS
76#endif
77
78#ifndef CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS
79#define CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS SYM_CONF_MAX_TAG
80#endif
81
82/*
83 * Anyway, we configure the driver for at least 64 tags per LUN. :)
84 */
85#if SYM_CONF_MAX_TAG <= 64
86#define SYM_CONF_MAX_TAG_ORDER (6)
87#elif SYM_CONF_MAX_TAG <= 128
88#define SYM_CONF_MAX_TAG_ORDER (7)
89#else
90#define SYM_CONF_MAX_TAG_ORDER (8)
91#endif
92
93/*
94 * Max number of SG entries.
95 */
96#define SYM_CONF_MAX_SG (96)
97
98/*
99 * Driver setup structure.
100 *
101 * This structure is initialized from linux config options.
102 * It can be overridden at boot-up by the boot command line.
103 */
104struct sym_driver_setup {
105 u_short max_tag;
106 u_char burst_order;
107 u_char scsi_led;
108 u_char scsi_diff;
109 u_char irq_mode;
110 u_char scsi_bus_check;
111 u_char host_id;
112
113 u_char verbose;
114 u_char settle_delay;
115 u_char use_nvram;
116 u_long excludes[8];
117};
118
119#define SYM_SETUP_MAX_TAG sym_driver_setup.max_tag
120#define SYM_SETUP_BURST_ORDER sym_driver_setup.burst_order
121#define SYM_SETUP_SCSI_LED sym_driver_setup.scsi_led
122#define SYM_SETUP_SCSI_DIFF sym_driver_setup.scsi_diff
123#define SYM_SETUP_IRQ_MODE sym_driver_setup.irq_mode
124#define SYM_SETUP_SCSI_BUS_CHECK sym_driver_setup.scsi_bus_check
125#define SYM_SETUP_HOST_ID sym_driver_setup.host_id
126#define boot_verbose sym_driver_setup.verbose
127
128/*
129 * Initial setup.
130 *
131 * Can be overriden at startup by a command line.
132 */
133#define SYM_LINUX_DRIVER_SETUP { \
134 .max_tag = CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS, \
135 .burst_order = 7, \
136 .scsi_led = 1, \
137 .scsi_diff = 1, \
138 .irq_mode = 0, \
139 .scsi_bus_check = 1, \
140 .host_id = 7, \
141 .verbose = 0, \
142 .settle_delay = 3, \
143 .use_nvram = 1, \
144}
145
146extern struct sym_driver_setup sym_driver_setup;
147extern unsigned int sym_debug_flags;
148#define DEBUG_FLAGS sym_debug_flags
149
150/*
151 * Max number of targets.
152 * Maximum is 16 and you are advised not to change this value.
153 */
154#ifndef SYM_CONF_MAX_TARGET
155#define SYM_CONF_MAX_TARGET (16)
156#endif
157
158/*
159 * Max number of logical units.
160 * SPI-2 allows up to 64 logical units, but in real life, target
161 * that implements more that 7 logical units are pretty rare.
162 * Anyway, the cost of accepting up to 64 logical unit is low in
163 * this driver, thus going with the maximum is acceptable.
164 */
165#ifndef SYM_CONF_MAX_LUN
166#define SYM_CONF_MAX_LUN (64)
167#endif
168
169/*
170 * Max number of IO control blocks queued to the controller.
171 * Each entry needs 8 bytes and the queues are allocated contiguously.
172 * Since we donnot want to allocate more than a page, the theorical
173 * maximum is PAGE_SIZE/8. For safety, we announce a bit less to the
174 * access method. :)
175 * When not supplied, as it is suggested, the driver compute some
176 * good value for this parameter.
177 */
178/* #define SYM_CONF_MAX_START (PAGE_SIZE/8 - 16) */
179
180/*
181 * Support for Immediate Arbitration.
182 * Not advised.
183 */
184/* #define SYM_CONF_IARB_SUPPORT */
185
186/*
187 * Only relevant if IARB support configured.
188 * - Max number of successive settings of IARB hints.
189 * - Set IARB on arbitration lost.
190 */
191#define SYM_CONF_IARB_MAX 3
192#define SYM_CONF_SET_IARB_ON_ARB_LOST 1
193
194/*
195 * Returning wrong residuals may make problems.
196 * When zero, this define tells the driver to
197 * always return 0 as transfer residual.
198 * Btw, all my testings of residuals have succeeded.
199 */
200#define SYM_SETUP_RESIDUAL_SUPPORT 1
201
202#endif /* SYM53C8XX_H */
203

source code of linux/drivers/scsi/sym53c8xx_2/sym53c8xx.h