Warning: That file was not part of the compilation database. It may have many parsing errors.

1/*
2 * Timer/Counter Unit (TC) registers.
3 *
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License as published by
6 * the Free Software Foundation; either version 2 of the License, or
7 * (at your option) any later version.
8 */
9
10#ifndef ATMEL_TC_H
11#define ATMEL_TC_H
12
13#include <linux/compiler.h>
14#include <linux/list.h>
15
16/*
17 * Many 32-bit Atmel SOCs include one or more TC blocks, each of which holds
18 * three general-purpose 16-bit timers. These timers share one register bank.
19 * Depending on the SOC, each timer may have its own clock and IRQ, or those
20 * may be shared by the whole TC block.
21 *
22 * These TC blocks may have up to nine external pins: TCLK0..2 signals for
23 * clocks or clock gates, and per-timer TIOA and TIOB signals used for PWM
24 * or triggering. Those pins need to be set up for use with the TC block,
25 * else they will be used as GPIOs or for a different controller.
26 *
27 * Although we expect each TC block to have a platform_device node, those
28 * nodes are not what drivers bind to. Instead, they ask for a specific
29 * TC block, by number ... which is a common approach on systems with many
30 * timers. Then they use clk_get() and platform_get_irq() to get clock and
31 * IRQ resources.
32 */
33
34struct clk;
35
36/**
37 * struct atmel_tcb_config - SoC data for a Timer/Counter Block
38 * @counter_width: size in bits of a timer counter register
39 */
40struct atmel_tcb_config {
41 size_t counter_width;
42};
43
44/**
45 * struct atmel_tc - information about a Timer/Counter Block
46 * @pdev: physical device
47 * @regs: mapping through which the I/O registers can be accessed
48 * @id: block id
49 * @tcb_config: configuration data from SoC
50 * @irq: irq for each of the three channels
51 * @clk: internal clock source for each of the three channels
52 * @node: list node, for tclib internal use
53 * @allocated: if already used, for tclib internal use
54 *
55 * On some platforms, each TC channel has its own clocks and IRQs,
56 * while on others, all TC channels share the same clock and IRQ.
57 * Drivers should clk_enable() all the clocks they need even though
58 * all the entries in @clk may point to the same physical clock.
59 * Likewise, drivers should request irqs independently for each
60 * channel, but they must use IRQF_SHARED in case some of the entries
61 * in @irq are actually the same IRQ.
62 */
63struct atmel_tc {
64 struct platform_device *pdev;
65 void __iomem *regs;
66 int id;
67 const struct atmel_tcb_config *tcb_config;
68 int irq[3];
69 struct clk *clk[3];
70 struct clk *slow_clk;
71 struct list_head node;
72 bool allocated;
73};
74
75extern struct atmel_tc *atmel_tc_alloc(unsigned block);
76extern void atmel_tc_free(struct atmel_tc *tc);
77
78/* platform-specific ATMEL_TC_TIMER_CLOCKx divisors (0 means 32KiHz) */
79extern const u8 atmel_tc_divisors[5];
80
81
82/*
83 * Two registers have block-wide controls. These are: configuring the three
84 * "external" clocks (or event sources) used by the timer channels; and
85 * synchronizing the timers by resetting them all at once.
86 *
87 * "External" can mean "external to chip" using the TCLK0, TCLK1, or TCLK2
88 * signals. Or, it can mean "external to timer", using the TIOA output from
89 * one of the other two timers that's being run in waveform mode.
90 */
91
92#define ATMEL_TC_BCR 0xc0 /* TC Block Control Register */
93#define ATMEL_TC_SYNC (1 << 0) /* synchronize timers */
94
95#define ATMEL_TC_BMR 0xc4 /* TC Block Mode Register */
96#define ATMEL_TC_TC0XC0S (3 << 0) /* external clock 0 source */
97#define ATMEL_TC_TC0XC0S_TCLK0 (0 << 0)
98#define ATMEL_TC_TC0XC0S_NONE (1 << 0)
99#define ATMEL_TC_TC0XC0S_TIOA1 (2 << 0)
100#define ATMEL_TC_TC0XC0S_TIOA2 (3 << 0)
101#define ATMEL_TC_TC1XC1S (3 << 2) /* external clock 1 source */
102#define ATMEL_TC_TC1XC1S_TCLK1 (0 << 2)
103#define ATMEL_TC_TC1XC1S_NONE (1 << 2)
104#define ATMEL_TC_TC1XC1S_TIOA0 (2 << 2)
105#define ATMEL_TC_TC1XC1S_TIOA2 (3 << 2)
106#define ATMEL_TC_TC2XC2S (3 << 4) /* external clock 2 source */
107#define ATMEL_TC_TC2XC2S_TCLK2 (0 << 4)
108#define ATMEL_TC_TC2XC2S_NONE (1 << 4)
109#define ATMEL_TC_TC2XC2S_TIOA0 (2 << 4)
110#define ATMEL_TC_TC2XC2S_TIOA1 (3 << 4)
111
112
113/*
114 * Each TC block has three "channels", each with one counter and controls.
115 *
116 * Note that the semantics of ATMEL_TC_TIMER_CLOCKx (input clock selection
117 * when it's not "external") is silicon-specific. AT91 platforms use one
118 * set of definitions; AVR32 platforms use a different set. Don't hard-wire
119 * such knowledge into your code, use the global "atmel_tc_divisors" ...
120 * where index N is the divisor for clock N+1, else zero to indicate it uses
121 * the 32 KiHz clock.
122 *
123 * The timers can be chained in various ways, and operated in "waveform"
124 * generation mode (including PWM) or "capture" mode (to time events). In
125 * both modes, behavior can be configured in many ways.
126 *
127 * Each timer has two I/O pins, TIOA and TIOB. Waveform mode uses TIOA as a
128 * PWM output, and TIOB as either another PWM or as a trigger. Capture mode
129 * uses them only as inputs.
130 */
131#define ATMEL_TC_CHAN(idx) ((idx)*0x40)
132#define ATMEL_TC_REG(idx, reg) (ATMEL_TC_CHAN(idx) + ATMEL_TC_ ## reg)
133
134#define ATMEL_TC_CCR 0x00 /* Channel Control Register */
135#define ATMEL_TC_CLKEN (1 << 0) /* clock enable */
136#define ATMEL_TC_CLKDIS (1 << 1) /* clock disable */
137#define ATMEL_TC_SWTRG (1 << 2) /* software trigger */
138
139#define ATMEL_TC_CMR 0x04 /* Channel Mode Register */
140
141/* Both modes share some CMR bits */
142#define ATMEL_TC_TCCLKS (7 << 0) /* clock source */
143#define ATMEL_TC_TIMER_CLOCK1 (0 << 0)
144#define ATMEL_TC_TIMER_CLOCK2 (1 << 0)
145#define ATMEL_TC_TIMER_CLOCK3 (2 << 0)
146#define ATMEL_TC_TIMER_CLOCK4 (3 << 0)
147#define ATMEL_TC_TIMER_CLOCK5 (4 << 0)
148#define ATMEL_TC_XC0 (5 << 0)
149#define ATMEL_TC_XC1 (6 << 0)
150#define ATMEL_TC_XC2 (7 << 0)
151#define ATMEL_TC_CLKI (1 << 3) /* clock invert */
152#define ATMEL_TC_BURST (3 << 4) /* clock gating */
153#define ATMEL_TC_GATE_NONE (0 << 4)
154#define ATMEL_TC_GATE_XC0 (1 << 4)
155#define ATMEL_TC_GATE_XC1 (2 << 4)
156#define ATMEL_TC_GATE_XC2 (3 << 4)
157#define ATMEL_TC_WAVE (1 << 15) /* true = Waveform mode */
158
159/* CAPTURE mode CMR bits */
160#define ATMEL_TC_LDBSTOP (1 << 6) /* counter stops on RB load */
161#define ATMEL_TC_LDBDIS (1 << 7) /* counter disable on RB load */
162#define ATMEL_TC_ETRGEDG (3 << 8) /* external trigger edge */
163#define ATMEL_TC_ETRGEDG_NONE (0 << 8)
164#define ATMEL_TC_ETRGEDG_RISING (1 << 8)
165#define ATMEL_TC_ETRGEDG_FALLING (2 << 8)
166#define ATMEL_TC_ETRGEDG_BOTH (3 << 8)
167#define ATMEL_TC_ABETRG (1 << 10) /* external trigger is TIOA? */
168#define ATMEL_TC_CPCTRG (1 << 14) /* RC compare trigger enable */
169#define ATMEL_TC_LDRA (3 << 16) /* RA loading edge (of TIOA) */
170#define ATMEL_TC_LDRA_NONE (0 << 16)
171#define ATMEL_TC_LDRA_RISING (1 << 16)
172#define ATMEL_TC_LDRA_FALLING (2 << 16)
173#define ATMEL_TC_LDRA_BOTH (3 << 16)
174#define ATMEL_TC_LDRB (3 << 18) /* RB loading edge (of TIOA) */
175#define ATMEL_TC_LDRB_NONE (0 << 18)
176#define ATMEL_TC_LDRB_RISING (1 << 18)
177#define ATMEL_TC_LDRB_FALLING (2 << 18)
178#define ATMEL_TC_LDRB_BOTH (3 << 18)
179
180/* WAVEFORM mode CMR bits */
181#define ATMEL_TC_CPCSTOP (1 << 6) /* RC compare stops counter */
182#define ATMEL_TC_CPCDIS (1 << 7) /* RC compare disables counter */
183#define ATMEL_TC_EEVTEDG (3 << 8) /* external event edge */
184#define ATMEL_TC_EEVTEDG_NONE (0 << 8)
185#define ATMEL_TC_EEVTEDG_RISING (1 << 8)
186#define ATMEL_TC_EEVTEDG_FALLING (2 << 8)
187#define ATMEL_TC_EEVTEDG_BOTH (3 << 8)
188#define ATMEL_TC_EEVT (3 << 10) /* external event source */
189#define ATMEL_TC_EEVT_TIOB (0 << 10)
190#define ATMEL_TC_EEVT_XC0 (1 << 10)
191#define ATMEL_TC_EEVT_XC1 (2 << 10)
192#define ATMEL_TC_EEVT_XC2 (3 << 10)
193#define ATMEL_TC_ENETRG (1 << 12) /* external event is trigger */
194#define ATMEL_TC_WAVESEL (3 << 13) /* waveform type */
195#define ATMEL_TC_WAVESEL_UP (0 << 13)
196#define ATMEL_TC_WAVESEL_UPDOWN (1 << 13)
197#define ATMEL_TC_WAVESEL_UP_AUTO (2 << 13)
198#define ATMEL_TC_WAVESEL_UPDOWN_AUTO (3 << 13)
199#define ATMEL_TC_ACPA (3 << 16) /* RA compare changes TIOA */
200#define ATMEL_TC_ACPA_NONE (0 << 16)
201#define ATMEL_TC_ACPA_SET (1 << 16)
202#define ATMEL_TC_ACPA_CLEAR (2 << 16)
203#define ATMEL_TC_ACPA_TOGGLE (3 << 16)
204#define ATMEL_TC_ACPC (3 << 18) /* RC compare changes TIOA */
205#define ATMEL_TC_ACPC_NONE (0 << 18)
206#define ATMEL_TC_ACPC_SET (1 << 18)
207#define ATMEL_TC_ACPC_CLEAR (2 << 18)
208#define ATMEL_TC_ACPC_TOGGLE (3 << 18)
209#define ATMEL_TC_AEEVT (3 << 20) /* external event changes TIOA */
210#define ATMEL_TC_AEEVT_NONE (0 << 20)
211#define ATMEL_TC_AEEVT_SET (1 << 20)
212#define ATMEL_TC_AEEVT_CLEAR (2 << 20)
213#define ATMEL_TC_AEEVT_TOGGLE (3 << 20)
214#define ATMEL_TC_ASWTRG (3 << 22) /* software trigger changes TIOA */
215#define ATMEL_TC_ASWTRG_NONE (0 << 22)
216#define ATMEL_TC_ASWTRG_SET (1 << 22)
217#define ATMEL_TC_ASWTRG_CLEAR (2 << 22)
218#define ATMEL_TC_ASWTRG_TOGGLE (3 << 22)
219#define ATMEL_TC_BCPB (3 << 24) /* RB compare changes TIOB */
220#define ATMEL_TC_BCPB_NONE (0 << 24)
221#define ATMEL_TC_BCPB_SET (1 << 24)
222#define ATMEL_TC_BCPB_CLEAR (2 << 24)
223#define ATMEL_TC_BCPB_TOGGLE (3 << 24)
224#define ATMEL_TC_BCPC (3 << 26) /* RC compare changes TIOB */
225#define ATMEL_TC_BCPC_NONE (0 << 26)
226#define ATMEL_TC_BCPC_SET (1 << 26)
227#define ATMEL_TC_BCPC_CLEAR (2 << 26)
228#define ATMEL_TC_BCPC_TOGGLE (3 << 26)
229#define ATMEL_TC_BEEVT (3 << 28) /* external event changes TIOB */
230#define ATMEL_TC_BEEVT_NONE (0 << 28)
231#define ATMEL_TC_BEEVT_SET (1 << 28)
232#define ATMEL_TC_BEEVT_CLEAR (2 << 28)
233#define ATMEL_TC_BEEVT_TOGGLE (3 << 28)
234#define ATMEL_TC_BSWTRG (3 << 30) /* software trigger changes TIOB */
235#define ATMEL_TC_BSWTRG_NONE (0 << 30)
236#define ATMEL_TC_BSWTRG_SET (1 << 30)
237#define ATMEL_TC_BSWTRG_CLEAR (2 << 30)
238#define ATMEL_TC_BSWTRG_TOGGLE (3 << 30)
239
240#define ATMEL_TC_CV 0x10 /* counter Value */
241#define ATMEL_TC_RA 0x14 /* register A */
242#define ATMEL_TC_RB 0x18 /* register B */
243#define ATMEL_TC_RC 0x1c /* register C */
244
245#define ATMEL_TC_SR 0x20 /* status (read-only) */
246/* Status-only flags */
247#define ATMEL_TC_CLKSTA (1 << 16) /* clock enabled */
248#define ATMEL_TC_MTIOA (1 << 17) /* TIOA mirror */
249#define ATMEL_TC_MTIOB (1 << 18) /* TIOB mirror */
250
251#define ATMEL_TC_IER 0x24 /* interrupt enable (write-only) */
252#define ATMEL_TC_IDR 0x28 /* interrupt disable (write-only) */
253#define ATMEL_TC_IMR 0x2c /* interrupt mask (read-only) */
254
255/* Status and IRQ flags */
256#define ATMEL_TC_COVFS (1 << 0) /* counter overflow */
257#define ATMEL_TC_LOVRS (1 << 1) /* load overrun */
258#define ATMEL_TC_CPAS (1 << 2) /* RA compare */
259#define ATMEL_TC_CPBS (1 << 3) /* RB compare */
260#define ATMEL_TC_CPCS (1 << 4) /* RC compare */
261#define ATMEL_TC_LDRAS (1 << 5) /* RA loading */
262#define ATMEL_TC_LDRBS (1 << 6) /* RB loading */
263#define ATMEL_TC_ETRGS (1 << 7) /* external trigger */
264#define ATMEL_TC_ALL_IRQ (ATMEL_TC_COVFS | ATMEL_TC_LOVRS | \
265 ATMEL_TC_CPAS | ATMEL_TC_CPBS | \
266 ATMEL_TC_CPCS | ATMEL_TC_LDRAS | \
267 ATMEL_TC_LDRBS | ATMEL_TC_ETRGS) \
268 /* all IRQs */
269
270#endif
271

Warning: That file was not part of the compilation database. It may have many parsing errors.