1/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
2/* $Id: scc.h,v 1.29 1997/04/02 14:56:45 jreuter Exp jreuter $ */
3
4#ifndef _UAPI_SCC_H
5#define _UAPI_SCC_H
6
7#include <linux/sockios.h>
8
9/* selection of hardware types */
10
11#define PA0HZP 0x00 /* hardware type for PA0HZP SCC card and compatible */
12#define EAGLE 0x01 /* hardware type for EAGLE card */
13#define PC100 0x02 /* hardware type for PC100 card */
14#define PRIMUS 0x04 /* hardware type for PRIMUS-PC (DG9BL) card */
15#define DRSI 0x08 /* hardware type for DRSI PC*Packet card */
16#define BAYCOM 0x10 /* hardware type for BayCom (U)SCC */
17
18/* DEV ioctl() commands */
19
20enum SCC_ioctl_cmds {
21 SIOCSCCRESERVED = SIOCDEVPRIVATE,
22 SIOCSCCCFG,
23 SIOCSCCINI,
24 SIOCSCCCHANINI,
25 SIOCSCCSMEM,
26 SIOCSCCGKISS,
27 SIOCSCCSKISS,
28 SIOCSCCGSTAT,
29 SIOCSCCCAL
30};
31
32/* Device parameter control (from WAMPES) */
33
34enum L1_params {
35 PARAM_DATA,
36 PARAM_TXDELAY,
37 PARAM_PERSIST,
38 PARAM_SLOTTIME,
39 PARAM_TXTAIL,
40 PARAM_FULLDUP,
41 PARAM_SOFTDCD, /* was: PARAM_HW */
42 PARAM_MUTE, /* ??? */
43 PARAM_DTR,
44 PARAM_RTS,
45 PARAM_SPEED,
46 PARAM_ENDDELAY, /* ??? */
47 PARAM_GROUP,
48 PARAM_IDLE,
49 PARAM_MIN,
50 PARAM_MAXKEY,
51 PARAM_WAIT,
52 PARAM_MAXDEFER,
53 PARAM_TX,
54 PARAM_HWEVENT = 31,
55 PARAM_RETURN = 255 /* reset kiss mode */
56};
57
58/* fulldup parameter */
59
60enum FULLDUP_modes {
61 KISS_DUPLEX_HALF, /* normal CSMA operation */
62 KISS_DUPLEX_FULL, /* fullduplex, key down trx after transmission */
63 KISS_DUPLEX_LINK, /* fullduplex, key down trx after 'idletime' sec */
64 KISS_DUPLEX_OPTIMA /* fullduplex, let the protocol layer control the hw */
65};
66
67/* misc. parameters */
68
69#define TIMER_OFF 65535U /* to switch off timers */
70#define NO_SUCH_PARAM 65534U /* param not implemented */
71
72/* HWEVENT parameter */
73
74enum HWEVENT_opts {
75 HWEV_DCD_ON,
76 HWEV_DCD_OFF,
77 HWEV_ALL_SENT
78};
79
80/* channel grouping */
81
82#define RXGROUP 0100 /* if set, only tx when all channels clear */
83#define TXGROUP 0200 /* if set, don't transmit simultaneously */
84
85/* Tx/Rx clock sources */
86
87enum CLOCK_sources {
88 CLK_DPLL, /* normal halfduplex operation */
89 CLK_EXTERNAL, /* external clocking (G3RUH/DF9IC modems) */
90 CLK_DIVIDER, /* Rx = DPLL, Tx = divider (fullduplex with */
91 /* modems without clock regeneration */
92 CLK_BRG /* experimental fullduplex mode with DPLL/BRG for */
93 /* MODEMs without clock recovery */
94};
95
96/* Tx state */
97
98enum TX_state {
99 TXS_IDLE, /* Transmitter off, no data pending */
100 TXS_BUSY, /* waiting for permission to send / tailtime */
101 TXS_ACTIVE, /* Transmitter on, sending data */
102 TXS_NEWFRAME, /* reset CRC and send (next) frame */
103 TXS_IDLE2, /* Transmitter on, no data pending */
104 TXS_WAIT, /* Waiting for Mintime to expire */
105 TXS_TIMEOUT /* We had a transmission timeout */
106};
107
108typedef unsigned long io_port; /* type definition for an 'io port address' */
109
110/* SCC statistical information */
111
112struct scc_stat {
113 long rxints; /* Receiver interrupts */
114 long txints; /* Transmitter interrupts */
115 long exints; /* External/status interrupts */
116 long spints; /* Special receiver interrupts */
117
118 long txframes; /* Packets sent */
119 long rxframes; /* Number of Frames Actually Received */
120 long rxerrs; /* CRC Errors */
121 long txerrs; /* KISS errors */
122
123 unsigned int nospace; /* "Out of buffers" */
124 unsigned int rx_over; /* Receiver Overruns */
125 unsigned int tx_under; /* Transmitter Underruns */
126
127 unsigned int tx_state; /* Transmitter state */
128 int tx_queued; /* tx frames enqueued */
129
130 unsigned int maxqueue; /* allocated tx_buffers */
131 unsigned int bufsize; /* used buffersize */
132};
133
134struct scc_modem {
135 long speed; /* Line speed, bps */
136 char clocksrc; /* 0 = DPLL, 1 = external, 2 = divider */
137 char nrz; /* NRZ instead of NRZI */
138};
139
140struct scc_kiss_cmd {
141 int command; /* one of the KISS-Commands defined above */
142 unsigned param; /* KISS-Param */
143};
144
145struct scc_hw_config {
146 io_port data_a; /* data port channel A */
147 io_port ctrl_a; /* control port channel A */
148 io_port data_b; /* data port channel B */
149 io_port ctrl_b; /* control port channel B */
150 io_port vector_latch; /* INTACK-Latch (#) */
151 io_port special; /* special function port */
152
153 int irq; /* irq */
154 long clock; /* clock */
155 char option; /* command for function port */
156
157 char brand; /* hardware type */
158 char escc; /* use ext. features of a 8580/85180/85280 */
159};
160
161/* (#) only one INTACK latch allowed. */
162
163
164struct scc_mem_config {
165 unsigned int dummy;
166 unsigned int bufsize;
167};
168
169struct scc_calibrate {
170 unsigned int time;
171 unsigned char pattern;
172};
173
174#endif /* _UAPI_SCC_H */
175

source code of linux/include/uapi/linux/scc.h