1// SPDX-License-Identifier: GPL-2.0
2// Copyright (c) 2020 MediaTek Inc.
3
4#include <linux/clk.h>
5#include <linux/delay.h>
6#include <linux/device.h>
7#include <linux/gpio/consumer.h>
8#include <linux/i2c.h>
9#include <linux/module.h>
10#include <linux/pm_runtime.h>
11#include <linux/regulator/consumer.h>
12#include <linux/units.h>
13#include <media/media-entity.h>
14#include <media/v4l2-async.h>
15#include <media/v4l2-ctrls.h>
16#include <media/v4l2-fwnode.h>
17#include <media/v4l2-subdev.h>
18
19#define OV02A10_ID 0x2509
20#define OV02A10_ID_MASK GENMASK(15, 0)
21
22#define OV02A10_REG_CHIP_ID 0x02
23
24/* Bit[1] vertical upside down */
25/* Bit[0] horizontal mirror */
26#define REG_MIRROR_FLIP_CONTROL 0x3f
27
28/* Orientation */
29#define REG_MIRROR_FLIP_ENABLE 0x03
30
31/* Bit[2:0] MIPI transmission speed select */
32#define TX_SPEED_AREA_SEL 0xa1
33#define OV02A10_MIPI_TX_SPEED_DEFAULT 0x04
34
35#define REG_PAGE_SWITCH 0xfd
36#define REG_GLOBAL_EFFECTIVE 0x01
37#define REG_ENABLE BIT(0)
38
39#define REG_SC_CTRL_MODE 0xac
40#define SC_CTRL_MODE_STANDBY 0x00
41#define SC_CTRL_MODE_STREAMING 0x01
42
43/* Exposure control */
44#define OV02A10_EXP_SHIFT 8
45#define OV02A10_REG_EXPOSURE_H 0x03
46#define OV02A10_REG_EXPOSURE_L 0x04
47#define OV02A10_EXPOSURE_MIN 4
48#define OV02A10_EXPOSURE_MAX_MARGIN 4
49#define OV02A10_EXPOSURE_STEP 1
50
51/* Vblanking control */
52#define OV02A10_VTS_SHIFT 8
53#define OV02A10_REG_VTS_H 0x05
54#define OV02A10_REG_VTS_L 0x06
55#define OV02A10_VTS_MAX 0x209f
56#define OV02A10_BASE_LINES 1224
57
58/* Analog gain control */
59#define OV02A10_REG_GAIN 0x24
60#define OV02A10_GAIN_MIN 0x10
61#define OV02A10_GAIN_MAX 0xf8
62#define OV02A10_GAIN_STEP 0x01
63#define OV02A10_GAIN_DEFAULT 0x40
64
65/* Test pattern control */
66#define OV02A10_REG_TEST_PATTERN 0xb6
67
68#define OV02A10_LINK_FREQ_390MHZ (390 * HZ_PER_MHZ)
69#define OV02A10_ECLK_FREQ (24 * HZ_PER_MHZ)
70
71/* Number of lanes supported by this driver */
72#define OV02A10_DATA_LANES 1
73
74/* Bits per sample of sensor output */
75#define OV02A10_BITS_PER_SAMPLE 10
76
77static const char * const ov02a10_supply_names[] = {
78 "dovdd", /* Digital I/O power */
79 "avdd", /* Analog power */
80 "dvdd", /* Digital core power */
81};
82
83struct ov02a10_reg {
84 u8 addr;
85 u8 val;
86};
87
88struct ov02a10_reg_list {
89 u32 num_of_regs;
90 const struct ov02a10_reg *regs;
91};
92
93struct ov02a10_mode {
94 u32 width;
95 u32 height;
96 u32 exp_def;
97 u32 hts_def;
98 u32 vts_def;
99 const struct ov02a10_reg_list reg_list;
100};
101
102struct ov02a10 {
103 u32 eclk_freq;
104 /* Indication of MIPI transmission speed select */
105 u32 mipi_clock_voltage;
106
107 struct clk *eclk;
108 struct gpio_desc *pd_gpio;
109 struct gpio_desc *rst_gpio;
110 struct regulator_bulk_data supplies[ARRAY_SIZE(ov02a10_supply_names)];
111
112 bool streaming;
113 bool upside_down;
114
115 /*
116 * Serialize control access, get/set format, get selection
117 * and start streaming.
118 */
119 struct mutex mutex;
120 struct v4l2_subdev subdev;
121 struct media_pad pad;
122 struct v4l2_mbus_framefmt fmt;
123 struct v4l2_ctrl_handler ctrl_handler;
124 struct v4l2_ctrl *exposure;
125
126 const struct ov02a10_mode *cur_mode;
127};
128
129static inline struct ov02a10 *to_ov02a10(struct v4l2_subdev *sd)
130{
131 return container_of(sd, struct ov02a10, subdev);
132}
133
134/*
135 * eclk 24Mhz
136 * pclk 39Mhz
137 * linelength 934(0x3a6)
138 * framelength 1390(0x56E)
139 * grabwindow_width 1600
140 * grabwindow_height 1200
141 * max_framerate 30fps
142 * mipi_datarate per lane 780Mbps
143 */
144static const struct ov02a10_reg ov02a10_1600x1200_regs[] = {
145 {0xfd, 0x01},
146 {0xac, 0x00},
147 {0xfd, 0x00},
148 {0x2f, 0x29},
149 {0x34, 0x00},
150 {0x35, 0x21},
151 {0x30, 0x15},
152 {0x33, 0x01},
153 {0xfd, 0x01},
154 {0x44, 0x00},
155 {0x2a, 0x4c},
156 {0x2b, 0x1e},
157 {0x2c, 0x60},
158 {0x25, 0x11},
159 {0x03, 0x01},
160 {0x04, 0xae},
161 {0x09, 0x00},
162 {0x0a, 0x02},
163 {0x06, 0xa6},
164 {0x31, 0x00},
165 {0x24, 0x40},
166 {0x01, 0x01},
167 {0xfb, 0x73},
168 {0xfd, 0x01},
169 {0x16, 0x04},
170 {0x1c, 0x09},
171 {0x21, 0x42},
172 {0x12, 0x04},
173 {0x13, 0x10},
174 {0x11, 0x40},
175 {0x33, 0x81},
176 {0xd0, 0x00},
177 {0xd1, 0x01},
178 {0xd2, 0x00},
179 {0x50, 0x10},
180 {0x51, 0x23},
181 {0x52, 0x20},
182 {0x53, 0x10},
183 {0x54, 0x02},
184 {0x55, 0x20},
185 {0x56, 0x02},
186 {0x58, 0x48},
187 {0x5d, 0x15},
188 {0x5e, 0x05},
189 {0x66, 0x66},
190 {0x68, 0x68},
191 {0x6b, 0x00},
192 {0x6c, 0x00},
193 {0x6f, 0x40},
194 {0x70, 0x40},
195 {0x71, 0x0a},
196 {0x72, 0xf0},
197 {0x73, 0x10},
198 {0x75, 0x80},
199 {0x76, 0x10},
200 {0x84, 0x00},
201 {0x85, 0x10},
202 {0x86, 0x10},
203 {0x87, 0x00},
204 {0x8a, 0x22},
205 {0x8b, 0x22},
206 {0x19, 0xf1},
207 {0x29, 0x01},
208 {0xfd, 0x01},
209 {0x9d, 0x16},
210 {0xa0, 0x29},
211 {0xa1, 0x04},
212 {0xad, 0x62},
213 {0xae, 0x00},
214 {0xaf, 0x85},
215 {0xb1, 0x01},
216 {0x8e, 0x06},
217 {0x8f, 0x40},
218 {0x90, 0x04},
219 {0x91, 0xb0},
220 {0x45, 0x01},
221 {0x46, 0x00},
222 {0x47, 0x6c},
223 {0x48, 0x03},
224 {0x49, 0x8b},
225 {0x4a, 0x00},
226 {0x4b, 0x07},
227 {0x4c, 0x04},
228 {0x4d, 0xb7},
229 {0xf0, 0x40},
230 {0xf1, 0x40},
231 {0xf2, 0x40},
232 {0xf3, 0x40},
233 {0x3f, 0x00},
234 {0xfd, 0x01},
235 {0x05, 0x00},
236 {0x06, 0xa6},
237 {0xfd, 0x01},
238};
239
240static const char * const ov02a10_test_pattern_menu[] = {
241 "Disabled",
242 "Eight Vertical Colour Bars",
243};
244
245static const s64 link_freq_menu_items[] = {
246 OV02A10_LINK_FREQ_390MHZ,
247};
248
249static u64 to_pixel_rate(u32 f_index)
250{
251 u64 pixel_rate = link_freq_menu_items[f_index] * 2 * OV02A10_DATA_LANES;
252
253 do_div(pixel_rate, OV02A10_BITS_PER_SAMPLE);
254
255 return pixel_rate;
256}
257
258static const struct ov02a10_mode supported_modes[] = {
259 {
260 .width = 1600,
261 .height = 1200,
262 .exp_def = 0x01ae,
263 .hts_def = 0x03a6,
264 .vts_def = 0x056e,
265 .reg_list = {
266 .num_of_regs = ARRAY_SIZE(ov02a10_1600x1200_regs),
267 .regs = ov02a10_1600x1200_regs,
268 },
269 },
270};
271
272static int ov02a10_write_array(struct ov02a10 *ov02a10,
273 const struct ov02a10_reg_list *r_list)
274{
275 struct i2c_client *client = v4l2_get_subdevdata(sd: &ov02a10->subdev);
276 unsigned int i;
277 int ret;
278
279 for (i = 0; i < r_list->num_of_regs; i++) {
280 ret = i2c_smbus_write_byte_data(client, command: r_list->regs[i].addr,
281 value: r_list->regs[i].val);
282 if (ret < 0)
283 return ret;
284 }
285
286 return 0;
287}
288
289static void ov02a10_fill_fmt(const struct ov02a10_mode *mode,
290 struct v4l2_mbus_framefmt *fmt)
291{
292 fmt->width = mode->width;
293 fmt->height = mode->height;
294 fmt->field = V4L2_FIELD_NONE;
295}
296
297static int ov02a10_set_fmt(struct v4l2_subdev *sd,
298 struct v4l2_subdev_state *sd_state,
299 struct v4l2_subdev_format *fmt)
300{
301 struct ov02a10 *ov02a10 = to_ov02a10(sd);
302 struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
303 struct v4l2_mbus_framefmt *frame_fmt;
304 int ret = 0;
305
306 mutex_lock(&ov02a10->mutex);
307
308 if (ov02a10->streaming && fmt->which == V4L2_SUBDEV_FORMAT_ACTIVE) {
309 ret = -EBUSY;
310 goto out_unlock;
311 }
312
313 /* Only one sensor mode supported */
314 mbus_fmt->code = ov02a10->fmt.code;
315 ov02a10_fill_fmt(mode: ov02a10->cur_mode, fmt: mbus_fmt);
316
317 if (fmt->which == V4L2_SUBDEV_FORMAT_TRY)
318 frame_fmt = v4l2_subdev_state_get_format(sd_state, 0);
319 else
320 frame_fmt = &ov02a10->fmt;
321
322 *frame_fmt = *mbus_fmt;
323
324out_unlock:
325 mutex_unlock(lock: &ov02a10->mutex);
326 return ret;
327}
328
329static int ov02a10_get_fmt(struct v4l2_subdev *sd,
330 struct v4l2_subdev_state *sd_state,
331 struct v4l2_subdev_format *fmt)
332{
333 struct ov02a10 *ov02a10 = to_ov02a10(sd);
334 struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
335
336 mutex_lock(&ov02a10->mutex);
337
338 if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
339 fmt->format = *v4l2_subdev_state_get_format(sd_state,
340 fmt->pad);
341 } else {
342 fmt->format = ov02a10->fmt;
343 mbus_fmt->code = ov02a10->fmt.code;
344 ov02a10_fill_fmt(mode: ov02a10->cur_mode, fmt: mbus_fmt);
345 }
346
347 mutex_unlock(lock: &ov02a10->mutex);
348
349 return 0;
350}
351
352static int ov02a10_enum_mbus_code(struct v4l2_subdev *sd,
353 struct v4l2_subdev_state *sd_state,
354 struct v4l2_subdev_mbus_code_enum *code)
355{
356 struct ov02a10 *ov02a10 = to_ov02a10(sd);
357
358 if (code->index != 0)
359 return -EINVAL;
360
361 code->code = ov02a10->fmt.code;
362
363 return 0;
364}
365
366static int ov02a10_enum_frame_sizes(struct v4l2_subdev *sd,
367 struct v4l2_subdev_state *sd_state,
368 struct v4l2_subdev_frame_size_enum *fse)
369{
370 if (fse->index >= ARRAY_SIZE(supported_modes))
371 return -EINVAL;
372
373 fse->min_width = supported_modes[fse->index].width;
374 fse->max_width = supported_modes[fse->index].width;
375 fse->max_height = supported_modes[fse->index].height;
376 fse->min_height = supported_modes[fse->index].height;
377
378 return 0;
379}
380
381static int ov02a10_check_sensor_id(struct ov02a10 *ov02a10)
382{
383 struct i2c_client *client = v4l2_get_subdevdata(sd: &ov02a10->subdev);
384 u16 chip_id;
385 int ret;
386
387 /* Validate the chip ID */
388 ret = i2c_smbus_read_word_swapped(client, OV02A10_REG_CHIP_ID);
389 if (ret < 0)
390 return ret;
391
392 chip_id = le16_to_cpu((__force __le16)ret);
393
394 if ((chip_id & OV02A10_ID_MASK) != OV02A10_ID) {
395 dev_err(&client->dev, "unexpected sensor id(0x%04x)\n", chip_id);
396 return -EINVAL;
397 }
398
399 return 0;
400}
401
402static int ov02a10_power_on(struct device *dev)
403{
404 struct i2c_client *client = to_i2c_client(dev);
405 struct v4l2_subdev *sd = i2c_get_clientdata(client);
406 struct ov02a10 *ov02a10 = to_ov02a10(sd);
407 int ret;
408
409 gpiod_set_value_cansleep(desc: ov02a10->rst_gpio, value: 1);
410 gpiod_set_value_cansleep(desc: ov02a10->pd_gpio, value: 1);
411
412 ret = clk_prepare_enable(clk: ov02a10->eclk);
413 if (ret < 0) {
414 dev_err(dev, "failed to enable eclk\n");
415 return ret;
416 }
417
418 ret = regulator_bulk_enable(ARRAY_SIZE(ov02a10_supply_names),
419 consumers: ov02a10->supplies);
420 if (ret < 0) {
421 dev_err(dev, "failed to enable regulators\n");
422 goto disable_clk;
423 }
424 usleep_range(min: 5000, max: 6000);
425
426 gpiod_set_value_cansleep(desc: ov02a10->pd_gpio, value: 0);
427 usleep_range(min: 5000, max: 6000);
428
429 gpiod_set_value_cansleep(desc: ov02a10->rst_gpio, value: 0);
430 usleep_range(min: 5000, max: 6000);
431
432 ret = ov02a10_check_sensor_id(ov02a10);
433 if (ret)
434 goto disable_regulator;
435
436 return 0;
437
438disable_regulator:
439 regulator_bulk_disable(ARRAY_SIZE(ov02a10_supply_names),
440 consumers: ov02a10->supplies);
441disable_clk:
442 clk_disable_unprepare(clk: ov02a10->eclk);
443
444 return ret;
445}
446
447static int ov02a10_power_off(struct device *dev)
448{
449 struct i2c_client *client = to_i2c_client(dev);
450 struct v4l2_subdev *sd = i2c_get_clientdata(client);
451 struct ov02a10 *ov02a10 = to_ov02a10(sd);
452
453 gpiod_set_value_cansleep(desc: ov02a10->rst_gpio, value: 1);
454 clk_disable_unprepare(clk: ov02a10->eclk);
455 gpiod_set_value_cansleep(desc: ov02a10->pd_gpio, value: 1);
456 regulator_bulk_disable(ARRAY_SIZE(ov02a10_supply_names),
457 consumers: ov02a10->supplies);
458
459 return 0;
460}
461
462static int __ov02a10_start_stream(struct ov02a10 *ov02a10)
463{
464 struct i2c_client *client = v4l2_get_subdevdata(sd: &ov02a10->subdev);
465 const struct ov02a10_reg_list *reg_list;
466 int ret;
467
468 /* Apply default values of current mode */
469 reg_list = &ov02a10->cur_mode->reg_list;
470 ret = ov02a10_write_array(ov02a10, r_list: reg_list);
471 if (ret)
472 return ret;
473
474 /* Apply customized values from user */
475 ret = __v4l2_ctrl_handler_setup(hdl: ov02a10->subdev.ctrl_handler);
476 if (ret)
477 return ret;
478
479 /* Set orientation to 180 degree */
480 if (ov02a10->upside_down) {
481 ret = i2c_smbus_write_byte_data(client, REG_MIRROR_FLIP_CONTROL,
482 REG_MIRROR_FLIP_ENABLE);
483 if (ret < 0) {
484 dev_err(&client->dev, "failed to set orientation\n");
485 return ret;
486 }
487 ret = i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
488 REG_ENABLE);
489 if (ret < 0)
490 return ret;
491 }
492
493 /* Set MIPI TX speed according to DT property */
494 if (ov02a10->mipi_clock_voltage != OV02A10_MIPI_TX_SPEED_DEFAULT) {
495 ret = i2c_smbus_write_byte_data(client, TX_SPEED_AREA_SEL,
496 value: ov02a10->mipi_clock_voltage);
497 if (ret < 0)
498 return ret;
499 }
500
501 /* Set stream on register */
502 return i2c_smbus_write_byte_data(client, REG_SC_CTRL_MODE,
503 SC_CTRL_MODE_STREAMING);
504}
505
506static int __ov02a10_stop_stream(struct ov02a10 *ov02a10)
507{
508 struct i2c_client *client = v4l2_get_subdevdata(sd: &ov02a10->subdev);
509
510 return i2c_smbus_write_byte_data(client, REG_SC_CTRL_MODE,
511 SC_CTRL_MODE_STANDBY);
512}
513
514static int ov02a10_init_state(struct v4l2_subdev *sd,
515 struct v4l2_subdev_state *sd_state)
516{
517 struct v4l2_subdev_format fmt = {
518 .which = V4L2_SUBDEV_FORMAT_TRY,
519 .format = {
520 .width = 1600,
521 .height = 1200,
522 }
523 };
524
525 ov02a10_set_fmt(sd, sd_state, fmt: &fmt);
526
527 return 0;
528}
529
530static int ov02a10_s_stream(struct v4l2_subdev *sd, int on)
531{
532 struct ov02a10 *ov02a10 = to_ov02a10(sd);
533 struct i2c_client *client = v4l2_get_subdevdata(sd: &ov02a10->subdev);
534 int ret;
535
536 mutex_lock(&ov02a10->mutex);
537
538 if (ov02a10->streaming == on) {
539 ret = 0;
540 goto unlock_and_return;
541 }
542
543 if (on) {
544 ret = pm_runtime_resume_and_get(dev: &client->dev);
545 if (ret < 0)
546 goto unlock_and_return;
547
548 ret = __ov02a10_start_stream(ov02a10);
549 if (ret) {
550 __ov02a10_stop_stream(ov02a10);
551 ov02a10->streaming = !on;
552 goto err_rpm_put;
553 }
554 } else {
555 __ov02a10_stop_stream(ov02a10);
556 pm_runtime_put(dev: &client->dev);
557 }
558
559 ov02a10->streaming = on;
560 mutex_unlock(lock: &ov02a10->mutex);
561
562 return 0;
563
564err_rpm_put:
565 pm_runtime_put(dev: &client->dev);
566unlock_and_return:
567 mutex_unlock(lock: &ov02a10->mutex);
568
569 return ret;
570}
571
572static const struct dev_pm_ops ov02a10_pm_ops = {
573 SET_RUNTIME_PM_OPS(ov02a10_power_off, ov02a10_power_on, NULL)
574};
575
576static int ov02a10_set_exposure(struct ov02a10 *ov02a10, int val)
577{
578 struct i2c_client *client = v4l2_get_subdevdata(sd: &ov02a10->subdev);
579 int ret;
580
581 ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
582 if (ret < 0)
583 return ret;
584
585 ret = i2c_smbus_write_byte_data(client, OV02A10_REG_EXPOSURE_H,
586 value: val >> OV02A10_EXP_SHIFT);
587 if (ret < 0)
588 return ret;
589
590 ret = i2c_smbus_write_byte_data(client, OV02A10_REG_EXPOSURE_L, value: val);
591 if (ret < 0)
592 return ret;
593
594 return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
595 REG_ENABLE);
596}
597
598static int ov02a10_set_gain(struct ov02a10 *ov02a10, int val)
599{
600 struct i2c_client *client = v4l2_get_subdevdata(sd: &ov02a10->subdev);
601 int ret;
602
603 ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
604 if (ret < 0)
605 return ret;
606
607 ret = i2c_smbus_write_byte_data(client, OV02A10_REG_GAIN, value: val);
608 if (ret < 0)
609 return ret;
610
611 return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
612 REG_ENABLE);
613}
614
615static int ov02a10_set_vblank(struct ov02a10 *ov02a10, int val)
616{
617 struct i2c_client *client = v4l2_get_subdevdata(sd: &ov02a10->subdev);
618 u32 vts = val + ov02a10->cur_mode->height - OV02A10_BASE_LINES;
619 int ret;
620
621 ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
622 if (ret < 0)
623 return ret;
624
625 ret = i2c_smbus_write_byte_data(client, OV02A10_REG_VTS_H,
626 value: vts >> OV02A10_VTS_SHIFT);
627 if (ret < 0)
628 return ret;
629
630 ret = i2c_smbus_write_byte_data(client, OV02A10_REG_VTS_L, value: vts);
631 if (ret < 0)
632 return ret;
633
634 return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
635 REG_ENABLE);
636}
637
638static int ov02a10_set_test_pattern(struct ov02a10 *ov02a10, int pattern)
639{
640 struct i2c_client *client = v4l2_get_subdevdata(sd: &ov02a10->subdev);
641 int ret;
642
643 ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
644 if (ret < 0)
645 return ret;
646
647 ret = i2c_smbus_write_byte_data(client, OV02A10_REG_TEST_PATTERN,
648 value: pattern);
649 if (ret < 0)
650 return ret;
651
652 ret = i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
653 REG_ENABLE);
654 if (ret < 0)
655 return ret;
656
657 return i2c_smbus_write_byte_data(client, REG_SC_CTRL_MODE,
658 SC_CTRL_MODE_STREAMING);
659}
660
661static int ov02a10_set_ctrl(struct v4l2_ctrl *ctrl)
662{
663 struct ov02a10 *ov02a10 = container_of(ctrl->handler,
664 struct ov02a10, ctrl_handler);
665 struct i2c_client *client = v4l2_get_subdevdata(sd: &ov02a10->subdev);
666 s64 max_expo;
667 int ret;
668
669 /* Propagate change of current control to all related controls */
670 if (ctrl->id == V4L2_CID_VBLANK) {
671 /* Update max exposure while meeting expected vblanking */
672 max_expo = ov02a10->cur_mode->height + ctrl->val -
673 OV02A10_EXPOSURE_MAX_MARGIN;
674 __v4l2_ctrl_modify_range(ctrl: ov02a10->exposure,
675 min: ov02a10->exposure->minimum, max: max_expo,
676 step: ov02a10->exposure->step,
677 def: ov02a10->exposure->default_value);
678 }
679
680 /* V4L2 controls values will be applied only when power is already up */
681 if (!pm_runtime_get_if_in_use(dev: &client->dev))
682 return 0;
683
684 switch (ctrl->id) {
685 case V4L2_CID_EXPOSURE:
686 ret = ov02a10_set_exposure(ov02a10, val: ctrl->val);
687 break;
688 case V4L2_CID_ANALOGUE_GAIN:
689 ret = ov02a10_set_gain(ov02a10, val: ctrl->val);
690 break;
691 case V4L2_CID_VBLANK:
692 ret = ov02a10_set_vblank(ov02a10, val: ctrl->val);
693 break;
694 case V4L2_CID_TEST_PATTERN:
695 ret = ov02a10_set_test_pattern(ov02a10, pattern: ctrl->val);
696 break;
697 default:
698 ret = -EINVAL;
699 break;
700 }
701
702 pm_runtime_put(dev: &client->dev);
703
704 return ret;
705}
706
707static const struct v4l2_subdev_video_ops ov02a10_video_ops = {
708 .s_stream = ov02a10_s_stream,
709};
710
711static const struct v4l2_subdev_pad_ops ov02a10_pad_ops = {
712 .enum_mbus_code = ov02a10_enum_mbus_code,
713 .enum_frame_size = ov02a10_enum_frame_sizes,
714 .get_fmt = ov02a10_get_fmt,
715 .set_fmt = ov02a10_set_fmt,
716};
717
718static const struct v4l2_subdev_ops ov02a10_subdev_ops = {
719 .video = &ov02a10_video_ops,
720 .pad = &ov02a10_pad_ops,
721};
722
723static const struct v4l2_subdev_internal_ops ov02a10_internal_ops = {
724 .init_state = ov02a10_init_state,
725};
726
727static const struct media_entity_operations ov02a10_subdev_entity_ops = {
728 .link_validate = v4l2_subdev_link_validate,
729};
730
731static const struct v4l2_ctrl_ops ov02a10_ctrl_ops = {
732 .s_ctrl = ov02a10_set_ctrl,
733};
734
735static int ov02a10_initialize_controls(struct ov02a10 *ov02a10)
736{
737 struct i2c_client *client = v4l2_get_subdevdata(sd: &ov02a10->subdev);
738 const struct ov02a10_mode *mode;
739 struct v4l2_ctrl_handler *handler;
740 struct v4l2_ctrl *ctrl;
741 s64 exposure_max;
742 s64 vblank_def;
743 s64 pixel_rate;
744 s64 h_blank;
745 int ret;
746
747 handler = &ov02a10->ctrl_handler;
748 mode = ov02a10->cur_mode;
749 ret = v4l2_ctrl_handler_init(handler, 7);
750 if (ret)
751 return ret;
752
753 handler->lock = &ov02a10->mutex;
754
755 ctrl = v4l2_ctrl_new_int_menu(hdl: handler, NULL, V4L2_CID_LINK_FREQ, max: 0, def: 0,
756 qmenu_int: link_freq_menu_items);
757 if (ctrl)
758 ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
759
760 pixel_rate = to_pixel_rate(f_index: 0);
761 v4l2_ctrl_new_std(hdl: handler, NULL, V4L2_CID_PIXEL_RATE, min: 0, max: pixel_rate, step: 1,
762 def: pixel_rate);
763
764 h_blank = mode->hts_def - mode->width;
765 v4l2_ctrl_new_std(hdl: handler, NULL, V4L2_CID_HBLANK, min: h_blank, max: h_blank, step: 1,
766 def: h_blank);
767
768 vblank_def = mode->vts_def - mode->height;
769 v4l2_ctrl_new_std(hdl: handler, ops: &ov02a10_ctrl_ops, V4L2_CID_VBLANK,
770 min: vblank_def, OV02A10_VTS_MAX - mode->height, step: 1,
771 def: vblank_def);
772
773 exposure_max = mode->vts_def - 4;
774 ov02a10->exposure = v4l2_ctrl_new_std(hdl: handler, ops: &ov02a10_ctrl_ops,
775 V4L2_CID_EXPOSURE,
776 OV02A10_EXPOSURE_MIN,
777 max: exposure_max,
778 OV02A10_EXPOSURE_STEP,
779 def: mode->exp_def);
780
781 v4l2_ctrl_new_std(hdl: handler, ops: &ov02a10_ctrl_ops,
782 V4L2_CID_ANALOGUE_GAIN, OV02A10_GAIN_MIN,
783 OV02A10_GAIN_MAX, OV02A10_GAIN_STEP,
784 OV02A10_GAIN_DEFAULT);
785
786 v4l2_ctrl_new_std_menu_items(hdl: handler, ops: &ov02a10_ctrl_ops,
787 V4L2_CID_TEST_PATTERN,
788 ARRAY_SIZE(ov02a10_test_pattern_menu) - 1,
789 mask: 0, def: 0, qmenu: ov02a10_test_pattern_menu);
790
791 if (handler->error) {
792 ret = handler->error;
793 dev_err(&client->dev, "failed to init controls(%d)\n", ret);
794 goto err_free_handler;
795 }
796
797 ov02a10->subdev.ctrl_handler = handler;
798
799 return 0;
800
801err_free_handler:
802 v4l2_ctrl_handler_free(hdl: handler);
803
804 return ret;
805}
806
807static int ov02a10_check_hwcfg(struct device *dev, struct ov02a10 *ov02a10)
808{
809 struct fwnode_handle *ep;
810 struct fwnode_handle *fwnode = dev_fwnode(dev);
811 struct v4l2_fwnode_endpoint bus_cfg = {
812 .bus_type = V4L2_MBUS_CSI2_DPHY,
813 };
814 unsigned int i, j;
815 u32 clk_volt;
816 int ret;
817
818 if (!fwnode)
819 return -EINVAL;
820
821 ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
822 if (!ep)
823 return -ENXIO;
824
825 ret = v4l2_fwnode_endpoint_alloc_parse(fwnode: ep, vep: &bus_cfg);
826 fwnode_handle_put(fwnode: ep);
827 if (ret)
828 return ret;
829
830 /* Optional indication of MIPI clock voltage unit */
831 ret = fwnode_property_read_u32(fwnode: ep, propname: "ovti,mipi-clock-voltage",
832 val: &clk_volt);
833
834 if (!ret)
835 ov02a10->mipi_clock_voltage = clk_volt;
836
837 for (i = 0; i < ARRAY_SIZE(link_freq_menu_items); i++) {
838 for (j = 0; j < bus_cfg.nr_of_link_frequencies; j++) {
839 if (link_freq_menu_items[i] ==
840 bus_cfg.link_frequencies[j])
841 break;
842 }
843
844 if (j == bus_cfg.nr_of_link_frequencies) {
845 dev_err(dev, "no link frequency %lld supported\n",
846 link_freq_menu_items[i]);
847 ret = -EINVAL;
848 break;
849 }
850 }
851
852 v4l2_fwnode_endpoint_free(vep: &bus_cfg);
853
854 return ret;
855}
856
857static int ov02a10_probe(struct i2c_client *client)
858{
859 struct device *dev = &client->dev;
860 struct ov02a10 *ov02a10;
861 unsigned int i;
862 unsigned int rotation;
863 int ret;
864
865 ov02a10 = devm_kzalloc(dev, size: sizeof(*ov02a10), GFP_KERNEL);
866 if (!ov02a10)
867 return -ENOMEM;
868
869 ret = ov02a10_check_hwcfg(dev, ov02a10);
870 if (ret)
871 return dev_err_probe(dev, err: ret,
872 fmt: "failed to check HW configuration\n");
873
874 v4l2_i2c_subdev_init(sd: &ov02a10->subdev, client, ops: &ov02a10_subdev_ops);
875 ov02a10->subdev.internal_ops = &ov02a10_internal_ops;
876
877 ov02a10->mipi_clock_voltage = OV02A10_MIPI_TX_SPEED_DEFAULT;
878 ov02a10->fmt.code = MEDIA_BUS_FMT_SBGGR10_1X10;
879
880 /* Optional indication of physical rotation of sensor */
881 rotation = 0;
882 device_property_read_u32(dev, propname: "rotation", val: &rotation);
883 if (rotation == 180) {
884 ov02a10->upside_down = true;
885 ov02a10->fmt.code = MEDIA_BUS_FMT_SRGGB10_1X10;
886 }
887
888 ov02a10->eclk = devm_clk_get(dev, id: "eclk");
889 if (IS_ERR(ptr: ov02a10->eclk))
890 return dev_err_probe(dev, err: PTR_ERR(ptr: ov02a10->eclk),
891 fmt: "failed to get eclk\n");
892
893 ret = device_property_read_u32(dev, propname: "clock-frequency",
894 val: &ov02a10->eclk_freq);
895 if (ret < 0)
896 return dev_err_probe(dev, err: ret,
897 fmt: "failed to get eclk frequency\n");
898
899 ret = clk_set_rate(clk: ov02a10->eclk, rate: ov02a10->eclk_freq);
900 if (ret < 0)
901 return dev_err_probe(dev, err: ret,
902 fmt: "failed to set eclk frequency (24MHz)\n");
903
904 if (clk_get_rate(clk: ov02a10->eclk) != OV02A10_ECLK_FREQ)
905 dev_warn(dev, "eclk mismatched, mode is based on 24MHz\n");
906
907 ov02a10->pd_gpio = devm_gpiod_get(dev, con_id: "powerdown", flags: GPIOD_OUT_HIGH);
908 if (IS_ERR(ptr: ov02a10->pd_gpio))
909 return dev_err_probe(dev, err: PTR_ERR(ptr: ov02a10->pd_gpio),
910 fmt: "failed to get powerdown-gpios\n");
911
912 ov02a10->rst_gpio = devm_gpiod_get(dev, con_id: "reset", flags: GPIOD_OUT_HIGH);
913 if (IS_ERR(ptr: ov02a10->rst_gpio))
914 return dev_err_probe(dev, err: PTR_ERR(ptr: ov02a10->rst_gpio),
915 fmt: "failed to get reset-gpios\n");
916
917 for (i = 0; i < ARRAY_SIZE(ov02a10_supply_names); i++)
918 ov02a10->supplies[i].supply = ov02a10_supply_names[i];
919
920 ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ov02a10_supply_names),
921 consumers: ov02a10->supplies);
922 if (ret)
923 return dev_err_probe(dev, err: ret, fmt: "failed to get regulators\n");
924
925 mutex_init(&ov02a10->mutex);
926
927 /* Set default mode */
928 ov02a10->cur_mode = &supported_modes[0];
929
930 ret = ov02a10_initialize_controls(ov02a10);
931 if (ret) {
932 dev_err_probe(dev, err: ret, fmt: "failed to initialize controls\n");
933 goto err_destroy_mutex;
934 }
935
936 /* Initialize subdev */
937 ov02a10->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
938 ov02a10->subdev.entity.ops = &ov02a10_subdev_entity_ops;
939 ov02a10->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR;
940 ov02a10->pad.flags = MEDIA_PAD_FL_SOURCE;
941
942 ret = media_entity_pads_init(entity: &ov02a10->subdev.entity, num_pads: 1, pads: &ov02a10->pad);
943 if (ret < 0) {
944 dev_err_probe(dev, err: ret, fmt: "failed to initialize entity pads\n");
945 goto err_free_handler;
946 }
947
948 pm_runtime_enable(dev);
949 if (!pm_runtime_enabled(dev)) {
950 ret = ov02a10_power_on(dev);
951 if (ret < 0) {
952 dev_err_probe(dev, err: ret, fmt: "failed to power on\n");
953 goto err_clean_entity;
954 }
955 }
956
957 ret = v4l2_async_register_subdev(sd: &ov02a10->subdev);
958 if (ret) {
959 dev_err_probe(dev, err: ret, fmt: "failed to register V4L2 subdev\n");
960 goto err_power_off;
961 }
962
963 return 0;
964
965err_power_off:
966 if (pm_runtime_enabled(dev))
967 pm_runtime_disable(dev);
968 else
969 ov02a10_power_off(dev);
970err_clean_entity:
971 media_entity_cleanup(entity: &ov02a10->subdev.entity);
972err_free_handler:
973 v4l2_ctrl_handler_free(hdl: ov02a10->subdev.ctrl_handler);
974err_destroy_mutex:
975 mutex_destroy(lock: &ov02a10->mutex);
976
977 return ret;
978}
979
980static void ov02a10_remove(struct i2c_client *client)
981{
982 struct v4l2_subdev *sd = i2c_get_clientdata(client);
983 struct ov02a10 *ov02a10 = to_ov02a10(sd);
984
985 v4l2_async_unregister_subdev(sd);
986 media_entity_cleanup(entity: &sd->entity);
987 v4l2_ctrl_handler_free(hdl: sd->ctrl_handler);
988 pm_runtime_disable(dev: &client->dev);
989 if (!pm_runtime_status_suspended(dev: &client->dev))
990 ov02a10_power_off(dev: &client->dev);
991 pm_runtime_set_suspended(dev: &client->dev);
992 mutex_destroy(lock: &ov02a10->mutex);
993}
994
995static const struct of_device_id ov02a10_of_match[] = {
996 { .compatible = "ovti,ov02a10" },
997 {}
998};
999MODULE_DEVICE_TABLE(of, ov02a10_of_match);
1000
1001static struct i2c_driver ov02a10_i2c_driver = {
1002 .driver = {
1003 .name = "ov02a10",
1004 .pm = &ov02a10_pm_ops,
1005 .of_match_table = ov02a10_of_match,
1006 },
1007 .probe = ov02a10_probe,
1008 .remove = ov02a10_remove,
1009};
1010module_i2c_driver(ov02a10_i2c_driver);
1011
1012MODULE_AUTHOR("Dongchun Zhu <dongchun.zhu@mediatek.com>");
1013MODULE_DESCRIPTION("OmniVision OV02A10 sensor driver");
1014MODULE_LICENSE("GPL v2");
1015

source code of linux/drivers/media/i2c/ov02a10.c