1/* atp.c: Attached (pocket) ethernet adapter driver for linux. */
2/*
3 This is a driver for commonly OEM pocket (parallel port)
4 ethernet adapters based on the Realtek RTL8002 and RTL8012 chips.
5
6 Written 1993-2000 by Donald Becker.
7
8 This software may be used and distributed according to the terms of
9 the GNU General Public License (GPL), incorporated herein by reference.
10 Drivers based on or derived from this code fall under the GPL and must
11 retain the authorship, copyright and license notice. This file is not
12 a complete program and may only be used when the entire operating
13 system is licensed under the GPL.
14
15 Copyright 1993 United States Government as represented by the Director,
16 National Security Agency. Copyright 1994-2000 retained by the original
17 author, Donald Becker. The timer-based reset code was supplied in 1995
18 by Bill Carlson, wwc@super.org.
19
20 The author may be reached as becker@scyld.com, or C/O
21 Scyld Computing Corporation
22 410 Severn Ave., Suite 210
23 Annapolis MD 21403
24
25 Support information and updates available at
26 http://www.scyld.com/network/atp.html
27
28
29 Modular support/softnet added by Alan Cox.
30 _bit abuse fixed up by Alan Cox
31
32*/
33
34static const char version[] =
35"atp.c:v1.09=ac 2002/10/01 Donald Becker <becker@scyld.com>\n";
36
37/* The user-configurable values.
38 These may be modified when a driver module is loaded.*/
39
40static int debug = 1; /* 1 normal messages, 0 quiet .. 7 verbose. */
41#define net_debug debug
42
43/* Maximum events (Rx packets, etc.) to handle at each interrupt. */
44static int max_interrupt_work = 15;
45
46#define NUM_UNITS 2
47/* The standard set of ISA module parameters. */
48static int io[NUM_UNITS];
49static int irq[NUM_UNITS];
50static int xcvr[NUM_UNITS]; /* The data transfer mode. */
51
52/* Operational parameters that are set at compile time. */
53
54/* Time in jiffies before concluding the transmitter is hung. */
55#define TX_TIMEOUT (400*HZ/1000)
56
57/*
58 This file is a device driver for the RealTek (aka AT-Lan-Tec) pocket
59 ethernet adapter. This is a common low-cost OEM pocket ethernet
60 adapter, sold under many names.
61
62 Sources:
63 This driver was written from the packet driver assembly code provided by
64 Vincent Bono of AT-Lan-Tec. Ever try to figure out how a complicated
65 device works just from the assembly code? It ain't pretty. The following
66 description is written based on guesses and writing lots of special-purpose
67 code to test my theorized operation.
68
69 In 1997 Realtek made available the documentation for the second generation
70 RTL8012 chip, which has lead to several driver improvements.
71 http://www.realtek.com.tw/
72
73 Theory of Operation
74
75 The RTL8002 adapter seems to be built around a custom spin of the SEEQ
76 controller core. It probably has a 16K or 64K internal packet buffer, of
77 which the first 4K is devoted to transmit and the rest to receive.
78 The controller maintains the queue of received packet and the packet buffer
79 access pointer internally, with only 'reset to beginning' and 'skip to next
80 packet' commands visible. The transmit packet queue holds two (or more?)
81 packets: both 'retransmit this packet' (due to collision) and 'transmit next
82 packet' commands must be started by hand.
83
84 The station address is stored in a standard bit-serial EEPROM which must be
85 read (ughh) by the device driver. (Provisions have been made for
86 substituting a 74S288 PROM, but I haven't gotten reports of any models
87 using it.) Unlike built-in devices, a pocket adapter can temporarily lose
88 power without indication to the device driver. The major effect is that
89 the station address, receive filter (promiscuous, etc.) and transceiver
90 must be reset.
91
92 The controller itself has 16 registers, some of which use only the lower
93 bits. The registers are read and written 4 bits at a time. The four bit
94 register address is presented on the data lines along with a few additional
95 timing and control bits. The data is then read from status port or written
96 to the data port.
97
98 Correction: the controller has two banks of 16 registers. The second
99 bank contains only the multicast filter table (now used) and the EEPROM
100 access registers.
101
102 Since the bulk data transfer of the actual packets through the slow
103 parallel port dominates the driver's running time, four distinct data
104 (non-register) transfer modes are provided by the adapter, two in each
105 direction. In the first mode timing for the nibble transfers is
106 provided through the data port. In the second mode the same timing is
107 provided through the control port. In either case the data is read from
108 the status port and written to the data port, just as it is accessing
109 registers.
110
111 In addition to the basic data transfer methods, several more are modes are
112 created by adding some delay by doing multiple reads of the data to allow
113 it to stabilize. This delay seems to be needed on most machines.
114
115 The data transfer mode is stored in the 'dev->if_port' field. Its default
116 value is '4'. It may be overridden at boot-time using the third parameter
117 to the "ether=..." initialization.
118
119 The header file <atp.h> provides inline functions that encapsulate the
120 register and data access methods. These functions are hand-tuned to
121 generate reasonable object code. This header file also documents my
122 interpretations of the device registers.
123*/
124
125#include <linux/kernel.h>
126#include <linux/module.h>
127#include <linux/types.h>
128#include <linux/fcntl.h>
129#include <linux/interrupt.h>
130#include <linux/ioport.h>
131#include <linux/in.h>
132#include <linux/string.h>
133#include <linux/errno.h>
134#include <linux/init.h>
135#include <linux/crc32.h>
136#include <linux/netdevice.h>
137#include <linux/etherdevice.h>
138#include <linux/skbuff.h>
139#include <linux/spinlock.h>
140#include <linux/delay.h>
141#include <linux/bitops.h>
142
143#include <asm/io.h>
144#include <asm/dma.h>
145
146#include "atp.h"
147
148MODULE_AUTHOR("Donald Becker <becker@scyld.com>");
149MODULE_DESCRIPTION("RealTek RTL8002/8012 parallel port Ethernet driver");
150MODULE_LICENSE("GPL");
151
152module_param(max_interrupt_work, int, 0);
153module_param(debug, int, 0);
154module_param_hw_array(io, int, ioport, NULL, 0);
155module_param_hw_array(irq, int, irq, NULL, 0);
156module_param_array(xcvr, int, NULL, 0);
157MODULE_PARM_DESC(max_interrupt_work, "ATP maximum events handled per interrupt");
158MODULE_PARM_DESC(debug, "ATP debug level (0-7)");
159MODULE_PARM_DESC(io, "ATP I/O base address(es)");
160MODULE_PARM_DESC(irq, "ATP IRQ number(s)");
161MODULE_PARM_DESC(xcvr, "ATP transceiver(s) (0=internal, 1=external)");
162
163/* The number of low I/O ports used by the ethercard. */
164#define ETHERCARD_TOTAL_SIZE 3
165
166/* Sequence to switch an 8012 from printer mux to ethernet mode. */
167static char mux_8012[] = { 0xff, 0xf7, 0xff, 0xfb, 0xf3, 0xfb, 0xff, 0xf7,};
168
169struct net_local {
170 spinlock_t lock;
171 struct net_device *next_module;
172 struct timer_list timer; /* Media selection timer. */
173 struct net_device *dev; /* Timer dev. */
174 unsigned long last_rx_time; /* Last Rx, in jiffies, to handle Rx hang. */
175 int saved_tx_size;
176 unsigned int tx_unit_busy:1;
177 unsigned char re_tx, /* Number of packet retransmissions. */
178 addr_mode, /* Current Rx filter e.g. promiscuous, etc. */
179 pac_cnt_in_tx_buf;
180};
181
182/* This code, written by wwc@super.org, resets the adapter every
183 TIMED_CHECKER ticks. This recovers from an unknown error which
184 hangs the device. */
185#define TIMED_CHECKER (HZ/4)
186#ifdef TIMED_CHECKER
187#include <linux/timer.h>
188static void atp_timed_checker(struct timer_list *t);
189#endif
190
191/* Index to functions, as function prototypes. */
192
193static int atp_probe1(long ioaddr);
194static void get_node_ID(struct net_device *dev);
195static unsigned short eeprom_op(long ioaddr, unsigned int cmd);
196static int net_open(struct net_device *dev);
197static void hardware_init(struct net_device *dev);
198static void write_packet(long ioaddr, int length, unsigned char *packet, int pad, int mode);
199static void trigger_send(long ioaddr, int length);
200static netdev_tx_t atp_send_packet(struct sk_buff *skb,
201 struct net_device *dev);
202static irqreturn_t atp_interrupt(int irq, void *dev_id);
203static void net_rx(struct net_device *dev);
204static void read_block(long ioaddr, int length, unsigned char *buffer, int data_mode);
205static int net_close(struct net_device *dev);
206static void set_rx_mode(struct net_device *dev);
207static void tx_timeout(struct net_device *dev, unsigned int txqueue);
208
209
210/* A list of all installed ATP devices, for removing the driver module. */
211static struct net_device *root_atp_dev;
212
213/* Check for a network adapter of this type, and return '0' iff one exists.
214 If dev->base_addr == 0, probe all likely locations.
215 If dev->base_addr == 1, always return failure.
216 If dev->base_addr == 2, allocate space for the device and return success
217 (detachable devices only).
218
219 FIXME: we should use the parport layer for this
220 */
221static int __init atp_init(void)
222{
223 int *port, ports[] = {0x378, 0x278, 0x3bc, 0};
224 int base_addr = io[0];
225
226 if (base_addr > 0x1ff) /* Check a single specified location. */
227 return atp_probe1(ioaddr: base_addr);
228 else if (base_addr == 1) /* Don't probe at all. */
229 return -ENXIO;
230
231 for (port = ports; *port; port++) {
232 long ioaddr = *port;
233 outb(value: 0x57, port: ioaddr + PAR_DATA);
234 if (inb(port: ioaddr + PAR_DATA) != 0x57)
235 continue;
236 if (atp_probe1(ioaddr) == 0)
237 return 0;
238 }
239
240 return -ENODEV;
241}
242
243static const struct net_device_ops atp_netdev_ops = {
244 .ndo_open = net_open,
245 .ndo_stop = net_close,
246 .ndo_start_xmit = atp_send_packet,
247 .ndo_set_rx_mode = set_rx_mode,
248 .ndo_tx_timeout = tx_timeout,
249 .ndo_set_mac_address = eth_mac_addr,
250 .ndo_validate_addr = eth_validate_addr,
251};
252
253static int __init atp_probe1(long ioaddr)
254{
255 struct net_device *dev = NULL;
256 struct net_local *lp;
257 int saved_ctrl_reg, status, i;
258 int res;
259
260 outb(value: 0xff, port: ioaddr + PAR_DATA);
261 /* Save the original value of the Control register, in case we guessed
262 wrong. */
263 saved_ctrl_reg = inb(port: ioaddr + PAR_CONTROL);
264 if (net_debug > 3)
265 printk("atp: Control register was %#2.2x.\n", saved_ctrl_reg);
266 /* IRQEN=0, SLCTB=high INITB=high, AUTOFDB=high, STBB=high. */
267 outb(value: 0x04, port: ioaddr + PAR_CONTROL);
268#ifndef final_version
269 if (net_debug > 3) {
270 /* Turn off the printer multiplexer on the 8012. */
271 for (i = 0; i < 8; i++)
272 outb(value: mux_8012[i], port: ioaddr + PAR_DATA);
273 write_reg(port: ioaddr, reg: MODSEL, value: 0x00);
274 printk("atp: Registers are ");
275 for (i = 0; i < 32; i++)
276 printk(" %2.2x", read_nibble(ioaddr, i));
277 printk(".\n");
278 }
279#endif
280 /* Turn off the printer multiplexer on the 8012. */
281 for (i = 0; i < 8; i++)
282 outb(value: mux_8012[i], port: ioaddr + PAR_DATA);
283 write_reg_high(port: ioaddr, reg: CMR1, CMR1h_RESET);
284 /* udelay() here? */
285 status = read_nibble(port: ioaddr, offset: CMR1);
286
287 if (net_debug > 3) {
288 printk(KERN_DEBUG "atp: Status nibble was %#2.2x..", status);
289 for (i = 0; i < 32; i++)
290 printk(" %2.2x", read_nibble(ioaddr, i));
291 printk("\n");
292 }
293
294 if ((status & 0x78) != 0x08) {
295 /* The pocket adapter probe failed, restore the control register. */
296 outb(value: saved_ctrl_reg, port: ioaddr + PAR_CONTROL);
297 return -ENODEV;
298 }
299 status = read_nibble(port: ioaddr, offset: CMR2_h);
300 if ((status & 0x78) != 0x10) {
301 outb(value: saved_ctrl_reg, port: ioaddr + PAR_CONTROL);
302 return -ENODEV;
303 }
304
305 dev = alloc_etherdev(sizeof(struct net_local));
306 if (!dev)
307 return -ENOMEM;
308
309 /* Find the IRQ used by triggering an interrupt. */
310 write_reg_byte(port: ioaddr, reg: CMR2, value: 0x01); /* No accept mode, IRQ out. */
311 write_reg_high(port: ioaddr, reg: CMR1, CMR1h_RxENABLE | CMR1h_TxENABLE); /* Enable Tx and Rx. */
312
313 /* Omit autoIRQ routine for now. Use "table lookup" instead. Uhgggh. */
314 if (irq[0])
315 dev->irq = irq[0];
316 else if (ioaddr == 0x378)
317 dev->irq = 7;
318 else
319 dev->irq = 5;
320 write_reg_high(port: ioaddr, reg: CMR1, CMR1h_TxRxOFF); /* Disable Tx and Rx units. */
321 write_reg(port: ioaddr, reg: CMR2, CMR2_NULL);
322
323 dev->base_addr = ioaddr;
324
325 /* Read the station address PROM. */
326 get_node_ID(dev);
327
328#ifndef MODULE
329 if (net_debug)
330 printk(KERN_INFO "%s", version);
331#endif
332
333 printk(KERN_NOTICE "%s: Pocket adapter found at %#3lx, IRQ %d, "
334 "SAPROM %pM.\n",
335 dev->name, dev->base_addr, dev->irq, dev->dev_addr);
336
337 /* Reset the ethernet hardware and activate the printer pass-through. */
338 write_reg_high(port: ioaddr, reg: CMR1, CMR1h_RESET | CMR1h_MUX);
339
340 lp = netdev_priv(dev);
341 lp->addr_mode = CMR2h_Normal;
342 spin_lock_init(&lp->lock);
343
344 /* For the ATP adapter the "if_port" is really the data transfer mode. */
345 if (xcvr[0])
346 dev->if_port = xcvr[0];
347 else
348 dev->if_port = (dev->mem_start & 0xf) ? (dev->mem_start & 0x7) : 4;
349 if (dev->mem_end & 0xf)
350 net_debug = dev->mem_end & 7;
351
352 dev->netdev_ops = &atp_netdev_ops;
353 dev->watchdog_timeo = TX_TIMEOUT;
354
355 res = register_netdev(dev);
356 if (res) {
357 free_netdev(dev);
358 return res;
359 }
360
361 lp->next_module = root_atp_dev;
362 root_atp_dev = dev;
363
364 return 0;
365}
366
367/* Read the station address PROM, usually a word-wide EEPROM. */
368static void __init get_node_ID(struct net_device *dev)
369{
370 long ioaddr = dev->base_addr;
371 __be16 addr[ETH_ALEN / 2];
372 int sa_offset = 0;
373 int i;
374
375 write_reg(port: ioaddr, reg: CMR2, CMR2_EEPROM); /* Point to the EEPROM control registers. */
376
377 /* Some adapters have the station address at offset 15 instead of offset
378 zero. Check for it, and fix it if needed. */
379 if (eeprom_op(ioaddr, EE_READ(0)) == 0xffff)
380 sa_offset = 15;
381
382 for (i = 0; i < 3; i++)
383 addr[i] =
384 cpu_to_be16(eeprom_op(ioaddr, EE_READ(sa_offset + i)));
385 eth_hw_addr_set(dev, addr: (u8 *)addr);
386
387 write_reg(port: ioaddr, reg: CMR2, CMR2_NULL);
388}
389
390/*
391 An EEPROM read command starts by shifting out 0x60+address, and then
392 shifting in the serial data. See the NatSemi databook for details.
393 * ________________
394 * CS : __|
395 * ___ ___
396 * CLK: ______| |___| |
397 * __ _______ _______
398 * DI : __X_______X_______X
399 * DO : _________X_______X
400 */
401
402static unsigned short __init eeprom_op(long ioaddr, u32 cmd)
403{
404 unsigned eedata_out = 0;
405 int num_bits = EE_CMD_SIZE;
406
407 while (--num_bits >= 0) {
408 char outval = (cmd & (1<<num_bits)) ? EE_DATA_WRITE : 0;
409 write_reg_high(port: ioaddr, reg: PROM_CMD, value: outval | EE_CLK_LOW);
410 write_reg_high(port: ioaddr, reg: PROM_CMD, value: outval | EE_CLK_HIGH);
411 eedata_out <<= 1;
412 if (read_nibble(port: ioaddr, offset: PROM_DATA) & EE_DATA_READ)
413 eedata_out++;
414 }
415 write_reg_high(port: ioaddr, reg: PROM_CMD, EE_CLK_LOW & ~EE_CS);
416 return eedata_out;
417}
418
419
420/* Open/initialize the board. This is called (in the current kernel)
421 sometime after booting when the 'ifconfig' program is run.
422
423 This routine sets everything up anew at each open, even
424 registers that "should" only need to be set once at boot, so that
425 there is non-reboot way to recover if something goes wrong.
426
427 This is an attachable device: if there is no private entry then it wasn't
428 probed for at boot-time, and we need to probe for it again.
429 */
430static int net_open(struct net_device *dev)
431{
432 struct net_local *lp = netdev_priv(dev);
433 int ret;
434
435 /* The interrupt line is turned off (tri-stated) when the device isn't in
436 use. That's especially important for "attached" interfaces where the
437 port or interrupt may be shared. */
438 ret = request_irq(irq: dev->irq, handler: atp_interrupt, flags: 0, name: dev->name, dev);
439 if (ret)
440 return ret;
441
442 hardware_init(dev);
443
444 lp->dev = dev;
445 timer_setup(&lp->timer, atp_timed_checker, 0);
446 lp->timer.expires = jiffies + TIMED_CHECKER;
447 add_timer(timer: &lp->timer);
448
449 netif_start_queue(dev);
450 return 0;
451}
452
453/* This routine resets the hardware. We initialize everything, assuming that
454 the hardware may have been temporarily detached. */
455static void hardware_init(struct net_device *dev)
456{
457 struct net_local *lp = netdev_priv(dev);
458 long ioaddr = dev->base_addr;
459 int i;
460
461 /* Turn off the printer multiplexer on the 8012. */
462 for (i = 0; i < 8; i++)
463 outb(value: mux_8012[i], port: ioaddr + PAR_DATA);
464 write_reg_high(port: ioaddr, reg: CMR1, CMR1h_RESET);
465
466 for (i = 0; i < 6; i++)
467 write_reg_byte(port: ioaddr, reg: PAR0 + i, value: dev->dev_addr[i]);
468
469 write_reg_high(port: ioaddr, reg: CMR2, value: lp->addr_mode);
470
471 if (net_debug > 2) {
472 printk(KERN_DEBUG "%s: Reset: current Rx mode %d.\n", dev->name,
473 (read_nibble(ioaddr, CMR2_h) >> 3) & 0x0f);
474 }
475
476 write_reg(port: ioaddr, reg: CMR2, CMR2_IRQOUT);
477 write_reg_high(port: ioaddr, reg: CMR1, CMR1h_RxENABLE | CMR1h_TxENABLE);
478
479 /* Enable the interrupt line from the serial port. */
480 outb(Ctrl_SelData + Ctrl_IRQEN, port: ioaddr + PAR_CONTROL);
481
482 /* Unmask the interesting interrupts. */
483 write_reg(port: ioaddr, reg: IMR, ISR_RxOK | ISR_TxErr | ISR_TxOK);
484 write_reg_high(port: ioaddr, reg: IMR, ISRh_RxErr);
485
486 lp->tx_unit_busy = 0;
487 lp->pac_cnt_in_tx_buf = 0;
488 lp->saved_tx_size = 0;
489}
490
491static void trigger_send(long ioaddr, int length)
492{
493 write_reg_byte(port: ioaddr, reg: TxCNT0, value: length & 0xff);
494 write_reg(port: ioaddr, reg: TxCNT1, value: length >> 8);
495 write_reg(port: ioaddr, reg: CMR1, CMR1_Xmit);
496}
497
498static void write_packet(long ioaddr, int length, unsigned char *packet, int pad_len, int data_mode)
499{
500 if (length & 1)
501 {
502 length++;
503 pad_len++;
504 }
505
506 outb(EOC+MAR, port: ioaddr + PAR_DATA);
507 if ((data_mode & 1) == 0) {
508 /* Write the packet out, starting with the write addr. */
509 outb(WrAddr+MAR, port: ioaddr + PAR_DATA);
510 do {
511 write_byte_mode0(ioaddr, value: *packet++);
512 } while (--length > pad_len) ;
513 do {
514 write_byte_mode0(ioaddr, value: 0);
515 } while (--length > 0) ;
516 } else {
517 /* Write the packet out in slow mode. */
518 unsigned char outbyte = *packet++;
519
520 outb(Ctrl_LNibWrite + Ctrl_IRQEN, port: ioaddr + PAR_CONTROL);
521 outb(WrAddr+MAR, port: ioaddr + PAR_DATA);
522
523 outb(value: (outbyte & 0x0f)|0x40, port: ioaddr + PAR_DATA);
524 outb(value: outbyte & 0x0f, port: ioaddr + PAR_DATA);
525 outbyte >>= 4;
526 outb(value: outbyte & 0x0f, port: ioaddr + PAR_DATA);
527 outb(Ctrl_HNibWrite + Ctrl_IRQEN, port: ioaddr + PAR_CONTROL);
528 while (--length > pad_len)
529 write_byte_mode1(ioaddr, value: *packet++);
530 while (--length > 0)
531 write_byte_mode1(ioaddr, value: 0);
532 }
533 /* Terminate the Tx frame. End of write: ECB. */
534 outb(value: 0xff, port: ioaddr + PAR_DATA);
535 outb(Ctrl_HNibWrite | Ctrl_SelData | Ctrl_IRQEN, port: ioaddr + PAR_CONTROL);
536}
537
538static void tx_timeout(struct net_device *dev, unsigned int txqueue)
539{
540 long ioaddr = dev->base_addr;
541
542 printk(KERN_WARNING "%s: Transmit timed out, %s?\n", dev->name,
543 inb(ioaddr + PAR_CONTROL) & 0x10 ? "network cable problem"
544 : "IRQ conflict");
545 dev->stats.tx_errors++;
546 /* Try to restart the adapter. */
547 hardware_init(dev);
548 netif_trans_update(dev); /* prevent tx timeout */
549 netif_wake_queue(dev);
550 dev->stats.tx_errors++;
551}
552
553static netdev_tx_t atp_send_packet(struct sk_buff *skb,
554 struct net_device *dev)
555{
556 struct net_local *lp = netdev_priv(dev);
557 long ioaddr = dev->base_addr;
558 int length;
559 unsigned long flags;
560
561 length = ETH_ZLEN < skb->len ? skb->len : ETH_ZLEN;
562
563 netif_stop_queue(dev);
564
565 /* Disable interrupts by writing 0x00 to the Interrupt Mask Register.
566 This sequence must not be interrupted by an incoming packet. */
567
568 spin_lock_irqsave(&lp->lock, flags);
569 write_reg(port: ioaddr, reg: IMR, value: 0);
570 write_reg_high(port: ioaddr, reg: IMR, value: 0);
571 spin_unlock_irqrestore(lock: &lp->lock, flags);
572
573 write_packet(ioaddr, length, packet: skb->data, pad_len: length-skb->len, data_mode: dev->if_port);
574
575 lp->pac_cnt_in_tx_buf++;
576 if (lp->tx_unit_busy == 0) {
577 trigger_send(ioaddr, length);
578 lp->saved_tx_size = 0; /* Redundant */
579 lp->re_tx = 0;
580 lp->tx_unit_busy = 1;
581 } else
582 lp->saved_tx_size = length;
583 /* Re-enable the LPT interrupts. */
584 write_reg(port: ioaddr, reg: IMR, ISR_RxOK | ISR_TxErr | ISR_TxOK);
585 write_reg_high(port: ioaddr, reg: IMR, ISRh_RxErr);
586
587 dev_kfree_skb (skb);
588 return NETDEV_TX_OK;
589}
590
591
592/* The typical workload of the driver:
593 Handle the network interface interrupts. */
594static irqreturn_t atp_interrupt(int irq, void *dev_instance)
595{
596 struct net_device *dev = dev_instance;
597 struct net_local *lp;
598 long ioaddr;
599 static int num_tx_since_rx;
600 int boguscount = max_interrupt_work;
601 int handled = 0;
602
603 ioaddr = dev->base_addr;
604 lp = netdev_priv(dev);
605
606 spin_lock(lock: &lp->lock);
607
608 /* Disable additional spurious interrupts. */
609 outb(Ctrl_SelData, port: ioaddr + PAR_CONTROL);
610
611 /* The adapter's output is currently the IRQ line, switch it to data. */
612 write_reg(port: ioaddr, reg: CMR2, CMR2_NULL);
613 write_reg(port: ioaddr, reg: IMR, value: 0);
614
615 if (net_debug > 5)
616 printk(KERN_DEBUG "%s: In interrupt ", dev->name);
617 while (--boguscount > 0) {
618 int status = read_nibble(port: ioaddr, offset: ISR);
619 if (net_debug > 5)
620 printk("loop status %02x..", status);
621
622 if (status & (ISR_RxOK<<3)) {
623 handled = 1;
624 write_reg(port: ioaddr, reg: ISR, ISR_RxOK); /* Clear the Rx interrupt. */
625 do {
626 int read_status = read_nibble(port: ioaddr, offset: CMR1);
627 if (net_debug > 6)
628 printk("handling Rx packet %02x..", read_status);
629 /* We acknowledged the normal Rx interrupt, so if the interrupt
630 is still outstanding we must have a Rx error. */
631 if (read_status & (CMR1_IRQ << 3)) { /* Overrun. */
632 dev->stats.rx_over_errors++;
633 /* Set to no-accept mode long enough to remove a packet. */
634 write_reg_high(port: ioaddr, reg: CMR2, CMR2h_OFF);
635 net_rx(dev);
636 /* Clear the interrupt and return to normal Rx mode. */
637 write_reg_high(port: ioaddr, reg: ISR, ISRh_RxErr);
638 write_reg_high(port: ioaddr, reg: CMR2, value: lp->addr_mode);
639 } else if ((read_status & (CMR1_BufEnb << 3)) == 0) {
640 net_rx(dev);
641 num_tx_since_rx = 0;
642 } else
643 break;
644 } while (--boguscount > 0);
645 } else if (status & ((ISR_TxErr + ISR_TxOK)<<3)) {
646 handled = 1;
647 if (net_debug > 6)
648 printk("handling Tx done..");
649 /* Clear the Tx interrupt. We should check for too many failures
650 and reinitialize the adapter. */
651 write_reg(port: ioaddr, reg: ISR, ISR_TxErr + ISR_TxOK);
652 if (status & (ISR_TxErr<<3)) {
653 dev->stats.collisions++;
654 if (++lp->re_tx > 15) {
655 dev->stats.tx_aborted_errors++;
656 hardware_init(dev);
657 break;
658 }
659 /* Attempt to retransmit. */
660 if (net_debug > 6) printk("attempting to ReTx");
661 write_reg(port: ioaddr, reg: CMR1, CMR1_ReXmit + CMR1_Xmit);
662 } else {
663 /* Finish up the transmit. */
664 dev->stats.tx_packets++;
665 lp->pac_cnt_in_tx_buf--;
666 if ( lp->saved_tx_size) {
667 trigger_send(ioaddr, length: lp->saved_tx_size);
668 lp->saved_tx_size = 0;
669 lp->re_tx = 0;
670 } else
671 lp->tx_unit_busy = 0;
672 netif_wake_queue(dev); /* Inform upper layers. */
673 }
674 num_tx_since_rx++;
675 } else if (num_tx_since_rx > 8 &&
676 time_after(jiffies, lp->last_rx_time + HZ)) {
677 if (net_debug > 2)
678 printk(KERN_DEBUG "%s: Missed packet? No Rx after %d Tx and "
679 "%ld jiffies status %02x CMR1 %02x.\n", dev->name,
680 num_tx_since_rx, jiffies - lp->last_rx_time, status,
681 (read_nibble(ioaddr, CMR1) >> 3) & 15);
682 dev->stats.rx_missed_errors++;
683 hardware_init(dev);
684 num_tx_since_rx = 0;
685 break;
686 } else
687 break;
688 }
689
690 /* This following code fixes a rare (and very difficult to track down)
691 problem where the adapter forgets its ethernet address. */
692 {
693 int i;
694 for (i = 0; i < 6; i++)
695 write_reg_byte(port: ioaddr, reg: PAR0 + i, value: dev->dev_addr[i]);
696#if 0 && defined(TIMED_CHECKER)
697 mod_timer(&lp->timer, jiffies + TIMED_CHECKER);
698#endif
699 }
700
701 /* Tell the adapter that it can go back to using the output line as IRQ. */
702 write_reg(port: ioaddr, reg: CMR2, CMR2_IRQOUT);
703 /* Enable the physical interrupt line, which is sure to be low until.. */
704 outb(Ctrl_SelData + Ctrl_IRQEN, port: ioaddr + PAR_CONTROL);
705 /* .. we enable the interrupt sources. */
706 write_reg(port: ioaddr, reg: IMR, ISR_RxOK | ISR_TxErr | ISR_TxOK);
707 write_reg_high(port: ioaddr, reg: IMR, ISRh_RxErr); /* Hmmm, really needed? */
708
709 spin_unlock(lock: &lp->lock);
710
711 if (net_debug > 5) printk("exiting interrupt.\n");
712 return IRQ_RETVAL(handled);
713}
714
715#ifdef TIMED_CHECKER
716/* This following code fixes a rare (and very difficult to track down)
717 problem where the adapter forgets its ethernet address. */
718static void atp_timed_checker(struct timer_list *t)
719{
720 struct net_local *lp = from_timer(lp, t, timer);
721 struct net_device *dev = lp->dev;
722 long ioaddr = dev->base_addr;
723 int tickssofar = jiffies - lp->last_rx_time;
724 int i;
725
726 spin_lock(lock: &lp->lock);
727 if (tickssofar > 2*HZ) {
728#if 1
729 for (i = 0; i < 6; i++)
730 write_reg_byte(port: ioaddr, reg: PAR0 + i, value: dev->dev_addr[i]);
731 lp->last_rx_time = jiffies;
732#else
733 for (i = 0; i < 6; i++)
734 if (read_cmd_byte(ioaddr, PAR0 + i) != atp_timed_dev->dev_addr[i])
735 {
736 struct net_local *lp = netdev_priv(atp_timed_dev);
737 write_reg_byte(ioaddr, PAR0 + i, atp_timed_dev->dev_addr[i]);
738 if (i == 2)
739 dev->stats.tx_errors++;
740 else if (i == 3)
741 dev->stats.tx_dropped++;
742 else if (i == 4)
743 dev->stats.collisions++;
744 else
745 dev->stats.rx_errors++;
746 }
747#endif
748 }
749 spin_unlock(lock: &lp->lock);
750 lp->timer.expires = jiffies + TIMED_CHECKER;
751 add_timer(timer: &lp->timer);
752}
753#endif
754
755/* We have a good packet(s), get it/them out of the buffers. */
756static void net_rx(struct net_device *dev)
757{
758 struct net_local *lp = netdev_priv(dev);
759 long ioaddr = dev->base_addr;
760 struct rx_header rx_head;
761
762 /* Process the received packet. */
763 outb(EOC+MAR, port: ioaddr + PAR_DATA);
764 read_block(ioaddr, length: 8, buffer: (unsigned char*)&rx_head, data_mode: dev->if_port);
765 if (net_debug > 5)
766 printk(KERN_DEBUG " rx_count %04x %04x %04x %04x..", rx_head.pad,
767 rx_head.rx_count, rx_head.rx_status, rx_head.cur_addr);
768 if ((rx_head.rx_status & 0x77) != 0x01) {
769 dev->stats.rx_errors++;
770 if (rx_head.rx_status & 0x0004) dev->stats.rx_frame_errors++;
771 else if (rx_head.rx_status & 0x0002) dev->stats.rx_crc_errors++;
772 if (net_debug > 3)
773 printk(KERN_DEBUG "%s: Unknown ATP Rx error %04x.\n",
774 dev->name, rx_head.rx_status);
775 if (rx_head.rx_status & 0x0020) {
776 dev->stats.rx_fifo_errors++;
777 write_reg_high(port: ioaddr, reg: CMR1, CMR1h_TxENABLE);
778 write_reg_high(port: ioaddr, reg: CMR1, CMR1h_RxENABLE | CMR1h_TxENABLE);
779 } else if (rx_head.rx_status & 0x0050)
780 hardware_init(dev);
781 return;
782 } else {
783 /* Malloc up new buffer. The "-4" omits the FCS (CRC). */
784 int pkt_len = (rx_head.rx_count & 0x7ff) - 4;
785 struct sk_buff *skb;
786
787 skb = netdev_alloc_skb(dev, length: pkt_len + 2);
788 if (skb == NULL) {
789 dev->stats.rx_dropped++;
790 goto done;
791 }
792
793 skb_reserve(skb, len: 2); /* Align IP on 16 byte boundaries */
794 read_block(ioaddr, length: pkt_len, buffer: skb_put(skb,len: pkt_len), data_mode: dev->if_port);
795 skb->protocol = eth_type_trans(skb, dev);
796 netif_rx(skb);
797 dev->stats.rx_packets++;
798 dev->stats.rx_bytes += pkt_len;
799 }
800 done:
801 write_reg(port: ioaddr, reg: CMR1, CMR1_NextPkt);
802 lp->last_rx_time = jiffies;
803}
804
805static void read_block(long ioaddr, int length, unsigned char *p, int data_mode)
806{
807 if (data_mode <= 3) { /* Mode 0 or 1 */
808 outb(Ctrl_LNibRead, port: ioaddr + PAR_CONTROL);
809 outb(value: length == 8 ? RdAddr | HNib | MAR : RdAddr | MAR,
810 port: ioaddr + PAR_DATA);
811 if (data_mode <= 1) { /* Mode 0 or 1 */
812 do { *p++ = read_byte_mode0(ioaddr); } while (--length > 0);
813 } else { /* Mode 2 or 3 */
814 do { *p++ = read_byte_mode2(ioaddr); } while (--length > 0);
815 }
816 } else if (data_mode <= 5) {
817 do { *p++ = read_byte_mode4(ioaddr); } while (--length > 0);
818 } else {
819 do { *p++ = read_byte_mode6(ioaddr); } while (--length > 0);
820 }
821
822 outb(EOC+HNib+MAR, port: ioaddr + PAR_DATA);
823 outb(Ctrl_SelData, port: ioaddr + PAR_CONTROL);
824}
825
826/* The inverse routine to net_open(). */
827static int
828net_close(struct net_device *dev)
829{
830 struct net_local *lp = netdev_priv(dev);
831 long ioaddr = dev->base_addr;
832
833 netif_stop_queue(dev);
834
835 del_timer_sync(timer: &lp->timer);
836
837 /* Flush the Tx and disable Rx here. */
838 lp->addr_mode = CMR2h_OFF;
839 write_reg_high(port: ioaddr, reg: CMR2, CMR2h_OFF);
840
841 /* Free the IRQ line. */
842 outb(value: 0x00, port: ioaddr + PAR_CONTROL);
843 free_irq(dev->irq, dev);
844
845 /* Reset the ethernet hardware and activate the printer pass-through. */
846 write_reg_high(port: ioaddr, reg: CMR1, CMR1h_RESET | CMR1h_MUX);
847 return 0;
848}
849
850/*
851 * Set or clear the multicast filter for this adapter.
852 */
853
854static void set_rx_mode(struct net_device *dev)
855{
856 struct net_local *lp = netdev_priv(dev);
857 long ioaddr = dev->base_addr;
858
859 if (!netdev_mc_empty(dev) || (dev->flags & (IFF_ALLMULTI|IFF_PROMISC)))
860 lp->addr_mode = CMR2h_PROMISC;
861 else
862 lp->addr_mode = CMR2h_Normal;
863 write_reg_high(port: ioaddr, reg: CMR2, value: lp->addr_mode);
864}
865
866static int __init atp_init_module(void) {
867 if (debug) /* Emit version even if no cards detected. */
868 printk(KERN_INFO "%s", version);
869 return atp_init();
870}
871
872static void __exit atp_cleanup_module(void) {
873 struct net_device *next_dev;
874
875 while (root_atp_dev) {
876 struct net_local *atp_local = netdev_priv(dev: root_atp_dev);
877 next_dev = atp_local->next_module;
878 unregister_netdev(dev: root_atp_dev);
879 /* No need to release_region(), since we never snarf it. */
880 free_netdev(dev: root_atp_dev);
881 root_atp_dev = next_dev;
882 }
883}
884
885module_init(atp_init_module);
886module_exit(atp_cleanup_module);
887

source code of linux/drivers/net/ethernet/realtek/atp.c