| 1 | /* SPDX-License-Identifier: GPL-2.0 */ |
|---|
| 2 | |
|---|
| 3 | /* 8530 Serial Communications Controller Register definitions */ |
|---|
| 4 | #define FLAG 0x7e |
|---|
| 5 | |
|---|
| 6 | /* Write Register 0 */ |
|---|
| 7 | #define R0 0 /* Register selects */ |
|---|
| 8 | #define R1 1 |
|---|
| 9 | #define R2 2 |
|---|
| 10 | #define R3 3 |
|---|
| 11 | #define R4 4 |
|---|
| 12 | #define R5 5 |
|---|
| 13 | #define R6 6 |
|---|
| 14 | #define R7 7 |
|---|
| 15 | #define R8 8 |
|---|
| 16 | #define R9 9 |
|---|
| 17 | #define R10 10 |
|---|
| 18 | #define R11 11 |
|---|
| 19 | #define R12 12 |
|---|
| 20 | #define R13 13 |
|---|
| 21 | #define R14 14 |
|---|
| 22 | #define R15 15 |
|---|
| 23 | |
|---|
| 24 | #define NULLCODE 0 /* Null Code */ |
|---|
| 25 | #define POINT_HIGH 0x8 /* Select upper half of registers */ |
|---|
| 26 | #define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */ |
|---|
| 27 | #define SEND_ABORT 0x18 /* HDLC Abort */ |
|---|
| 28 | #define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */ |
|---|
| 29 | #define RES_Tx_P 0x28 /* Reset TxINT Pending */ |
|---|
| 30 | #define ERR_RES 0x30 /* Error Reset */ |
|---|
| 31 | #define RES_H_IUS 0x38 /* Reset highest IUS */ |
|---|
| 32 | |
|---|
| 33 | #define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */ |
|---|
| 34 | #define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */ |
|---|
| 35 | #define RES_EOM_L 0xC0 /* Reset EOM latch */ |
|---|
| 36 | |
|---|
| 37 | /* Write Register 1 */ |
|---|
| 38 | |
|---|
| 39 | #define EXT_INT_ENAB 0x1 /* Ext Int Enable */ |
|---|
| 40 | #define TxINT_ENAB 0x2 /* Tx Int Enable */ |
|---|
| 41 | #define PAR_SPEC 0x4 /* Parity is special condition */ |
|---|
| 42 | |
|---|
| 43 | #define RxINT_DISAB 0 /* Rx Int Disable */ |
|---|
| 44 | #define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */ |
|---|
| 45 | #define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */ |
|---|
| 46 | #define INT_ERR_Rx 0x18 /* Int on error only */ |
|---|
| 47 | |
|---|
| 48 | #define WT_RDY_RT 0x20 /* Wait/Ready on R/T */ |
|---|
| 49 | #define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */ |
|---|
| 50 | #define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */ |
|---|
| 51 | |
|---|
| 52 | /* Write Register #2 (Interrupt Vector) */ |
|---|
| 53 | |
|---|
| 54 | /* Write Register 3 */ |
|---|
| 55 | |
|---|
| 56 | #define RxENABLE 0x1 /* Rx Enable */ |
|---|
| 57 | #define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */ |
|---|
| 58 | #define ADD_SM 0x4 /* Address Search Mode (SDLC) */ |
|---|
| 59 | #define RxCRC_ENAB 0x8 /* Rx CRC Enable */ |
|---|
| 60 | #define ENT_HM 0x10 /* Enter Hunt Mode */ |
|---|
| 61 | #define AUTO_ENAB 0x20 /* Auto Enables */ |
|---|
| 62 | #define Rx5 0x0 /* Rx 5 Bits/Character */ |
|---|
| 63 | #define Rx7 0x40 /* Rx 7 Bits/Character */ |
|---|
| 64 | #define Rx6 0x80 /* Rx 6 Bits/Character */ |
|---|
| 65 | #define Rx8 0xc0 /* Rx 8 Bits/Character */ |
|---|
| 66 | |
|---|
| 67 | /* Write Register 4 */ |
|---|
| 68 | |
|---|
| 69 | #define PAR_ENA 0x1 /* Parity Enable */ |
|---|
| 70 | #define PAR_EVEN 0x2 /* Parity Even/Odd* */ |
|---|
| 71 | |
|---|
| 72 | #define SYNC_ENAB 0 /* Sync Modes Enable */ |
|---|
| 73 | #define SB1 0x4 /* 1 stop bit/char */ |
|---|
| 74 | #define SB15 0x8 /* 1.5 stop bits/char */ |
|---|
| 75 | #define SB2 0xc /* 2 stop bits/char */ |
|---|
| 76 | |
|---|
| 77 | #define MONSYNC 0 /* 8 Bit Sync character */ |
|---|
| 78 | #define BISYNC 0x10 /* 16 bit sync character */ |
|---|
| 79 | #define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */ |
|---|
| 80 | #define EXTSYNC 0x30 /* External Sync Mode */ |
|---|
| 81 | |
|---|
| 82 | #define X1CLK 0x0 /* x1 clock mode */ |
|---|
| 83 | #define X16CLK 0x40 /* x16 clock mode */ |
|---|
| 84 | #define X32CLK 0x80 /* x32 clock mode */ |
|---|
| 85 | #define X64CLK 0xC0 /* x64 clock mode */ |
|---|
| 86 | |
|---|
| 87 | /* Write Register 5 */ |
|---|
| 88 | |
|---|
| 89 | #define TxCRC_ENAB 0x1 /* Tx CRC Enable */ |
|---|
| 90 | #define RTS 0x2 /* RTS */ |
|---|
| 91 | #define SDLC_CRC 0x4 /* SDLC/CRC-16 */ |
|---|
| 92 | #define TxENAB 0x8 /* Tx Enable */ |
|---|
| 93 | #define SND_BRK 0x10 /* Send Break */ |
|---|
| 94 | #define Tx5 0x0 /* Tx 5 bits (or less)/character */ |
|---|
| 95 | #define Tx7 0x20 /* Tx 7 bits/character */ |
|---|
| 96 | #define Tx6 0x40 /* Tx 6 bits/character */ |
|---|
| 97 | #define Tx8 0x60 /* Tx 8 bits/character */ |
|---|
| 98 | #define DTR 0x80 /* DTR */ |
|---|
| 99 | |
|---|
| 100 | /* Write Register 6 (Sync bits 0-7/SDLC Address Field) */ |
|---|
| 101 | |
|---|
| 102 | /* Write Register 7 (Sync bits 8-15/SDLC 01111110) */ |
|---|
| 103 | |
|---|
| 104 | /* Write Register 8 (transmit buffer) */ |
|---|
| 105 | |
|---|
| 106 | /* Write Register 9 (Master interrupt control) */ |
|---|
| 107 | #define VIS 1 /* Vector Includes Status */ |
|---|
| 108 | #define NV 2 /* No Vector */ |
|---|
| 109 | #define DLC 4 /* Disable Lower Chain */ |
|---|
| 110 | #define MIE 8 /* Master Interrupt Enable */ |
|---|
| 111 | #define STATHI 0x10 /* Status high */ |
|---|
| 112 | #define NORESET 0 /* No reset on write to R9 */ |
|---|
| 113 | #define CHRB 0x40 /* Reset channel B */ |
|---|
| 114 | #define CHRA 0x80 /* Reset channel A */ |
|---|
| 115 | #define FHWRES 0xc0 /* Force hardware reset */ |
|---|
| 116 | |
|---|
| 117 | /* Write Register 10 (misc control bits) */ |
|---|
| 118 | #define BIT6 1 /* 6 bit/8bit sync */ |
|---|
| 119 | #define LOOPMODE 2 /* SDLC Loop mode */ |
|---|
| 120 | #define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */ |
|---|
| 121 | #define MARKIDLE 8 /* Mark/flag on idle */ |
|---|
| 122 | #define GAOP 0x10 /* Go active on poll */ |
|---|
| 123 | #define NRZ 0 /* NRZ mode */ |
|---|
| 124 | #define NRZI 0x20 /* NRZI mode */ |
|---|
| 125 | #define FM1 0x40 /* FM1 (transition = 1) */ |
|---|
| 126 | #define FM0 0x60 /* FM0 (transition = 0) */ |
|---|
| 127 | #define CRCPS 0x80 /* CRC Preset I/O */ |
|---|
| 128 | |
|---|
| 129 | /* Write Register 11 (Clock Mode control) */ |
|---|
| 130 | #define TRxCXT 0 /* TRxC = Xtal output */ |
|---|
| 131 | #define TRxCTC 1 /* TRxC = Transmit clock */ |
|---|
| 132 | #define TRxCBR 2 /* TRxC = BR Generator Output */ |
|---|
| 133 | #define TRxCDP 3 /* TRxC = DPLL output */ |
|---|
| 134 | #define TRxCOI 4 /* TRxC O/I */ |
|---|
| 135 | #define TCRTxCP 0 /* Transmit clock = RTxC pin */ |
|---|
| 136 | #define TCTRxCP 8 /* Transmit clock = TRxC pin */ |
|---|
| 137 | #define TCBR 0x10 /* Transmit clock = BR Generator output */ |
|---|
| 138 | #define TCDPLL 0x18 /* Transmit clock = DPLL output */ |
|---|
| 139 | #define RCRTxCP 0 /* Receive clock = RTxC pin */ |
|---|
| 140 | #define RCTRxCP 0x20 /* Receive clock = TRxC pin */ |
|---|
| 141 | #define RCBR 0x40 /* Receive clock = BR Generator output */ |
|---|
| 142 | #define RCDPLL 0x60 /* Receive clock = DPLL output */ |
|---|
| 143 | #define RTxCX 0x80 /* RTxC Xtal/No Xtal */ |
|---|
| 144 | |
|---|
| 145 | /* Write Register 12 (lower byte of baud rate generator time constant) */ |
|---|
| 146 | |
|---|
| 147 | /* Write Register 13 (upper byte of baud rate generator time constant) */ |
|---|
| 148 | |
|---|
| 149 | /* Write Register 14 (Misc control bits) */ |
|---|
| 150 | #define BRENABL 1 /* Baud rate generator enable */ |
|---|
| 151 | #define BRSRC 2 /* Baud rate generator source */ |
|---|
| 152 | #define DTRREQ 4 /* DTR/Request function */ |
|---|
| 153 | #define AUTOECHO 8 /* Auto Echo */ |
|---|
| 154 | #define LOOPBAK 0x10 /* Local loopback */ |
|---|
| 155 | #define SEARCH 0x20 /* Enter search mode */ |
|---|
| 156 | #define RMC 0x40 /* Reset missing clock */ |
|---|
| 157 | #define DISDPLL 0x60 /* Disable DPLL */ |
|---|
| 158 | #define SSBR 0x80 /* Set DPLL source = BR generator */ |
|---|
| 159 | #define SSRTxC 0xa0 /* Set DPLL source = RTxC */ |
|---|
| 160 | #define SFMM 0xc0 /* Set FM mode */ |
|---|
| 161 | #define SNRZI 0xe0 /* Set NRZI mode */ |
|---|
| 162 | |
|---|
| 163 | /* Write Register 15 (external/status interrupt control) */ |
|---|
| 164 | #define ZCIE 2 /* Zero count IE */ |
|---|
| 165 | #define DCDIE 8 /* DCD IE */ |
|---|
| 166 | #define SYNCIE 0x10 /* Sync/hunt IE */ |
|---|
| 167 | #define CTSIE 0x20 /* CTS IE */ |
|---|
| 168 | #define TxUIE 0x40 /* Tx Underrun/EOM IE */ |
|---|
| 169 | #define BRKIE 0x80 /* Break/Abort IE */ |
|---|
| 170 | |
|---|
| 171 | |
|---|
| 172 | /* Read Register 0 */ |
|---|
| 173 | #define Rx_CH_AV 0x1 /* Rx Character Available */ |
|---|
| 174 | #define ZCOUNT 0x2 /* Zero count */ |
|---|
| 175 | #define Tx_BUF_EMP 0x4 /* Tx Buffer empty */ |
|---|
| 176 | #define DCD 0x8 /* DCD */ |
|---|
| 177 | #define SYNC_HUNT 0x10 /* Sync/hunt */ |
|---|
| 178 | #define CTS 0x20 /* CTS */ |
|---|
| 179 | #define TxEOM 0x40 /* Tx underrun */ |
|---|
| 180 | #define BRK_ABRT 0x80 /* Break/Abort */ |
|---|
| 181 | |
|---|
| 182 | /* Read Register 1 */ |
|---|
| 183 | #define ALL_SNT 0x1 /* All sent */ |
|---|
| 184 | /* Residue Data for 8 Rx bits/char programmed */ |
|---|
| 185 | #define RES3 0x8 /* 0/3 */ |
|---|
| 186 | #define RES4 0x4 /* 0/4 */ |
|---|
| 187 | #define RES5 0xc /* 0/5 */ |
|---|
| 188 | #define RES6 0x2 /* 0/6 */ |
|---|
| 189 | #define RES7 0xa /* 0/7 */ |
|---|
| 190 | #define RES8 0x6 /* 0/8 */ |
|---|
| 191 | #define RES18 0xe /* 1/8 */ |
|---|
| 192 | #define RES28 0x0 /* 2/8 */ |
|---|
| 193 | /* Special Rx Condition Interrupts */ |
|---|
| 194 | #define PAR_ERR 0x10 /* Parity error */ |
|---|
| 195 | #define Rx_OVR 0x20 /* Rx Overrun Error */ |
|---|
| 196 | #define CRC_ERR 0x40 /* CRC/Framing Error */ |
|---|
| 197 | #define END_FR 0x80 /* End of Frame (SDLC) */ |
|---|
| 198 | |
|---|
| 199 | /* Read Register 2 (channel b only) - Interrupt vector */ |
|---|
| 200 | |
|---|
| 201 | /* Read Register 3 (interrupt pending register) ch a only */ |
|---|
| 202 | #define CHBEXT 0x1 /* Channel B Ext/Stat IP */ |
|---|
| 203 | #define CHBTxIP 0x2 /* Channel B Tx IP */ |
|---|
| 204 | #define CHBRxIP 0x4 /* Channel B Rx IP */ |
|---|
| 205 | #define CHAEXT 0x8 /* Channel A Ext/Stat IP */ |
|---|
| 206 | #define CHATxIP 0x10 /* Channel A Tx IP */ |
|---|
| 207 | #define CHARxIP 0x20 /* Channel A Rx IP */ |
|---|
| 208 | |
|---|
| 209 | /* Read Register 8 (receive data register) */ |
|---|
| 210 | |
|---|
| 211 | /* Read Register 10 (misc status bits) */ |
|---|
| 212 | #define ONLOOP 2 /* On loop */ |
|---|
| 213 | #define LOOPSEND 0x10 /* Loop sending */ |
|---|
| 214 | #define CLK2MIS 0x40 /* Two clocks missing */ |
|---|
| 215 | #define CLK1MIS 0x80 /* One clock missing */ |
|---|
| 216 | |
|---|
| 217 | /* Read Register 12 (lower byte of baud rate generator constant) */ |
|---|
| 218 | |
|---|
| 219 | /* Read Register 13 (upper byte of baud rate generator constant) */ |
|---|
| 220 | |
|---|
| 221 | /* Read Register 15 (value of WR 15) */ |
|---|
| 222 | |
|---|
| 223 | /* Z85C30/Z85230 Enhanced SCC register definitions */ |
|---|
| 224 | |
|---|
| 225 | /* Write Register 7' (SDLC/HDLC Programmable Enhancements) */ |
|---|
| 226 | #define AUTOTXF 0x01 /* Auto Tx Flag */ |
|---|
| 227 | #define AUTOEOM 0x02 /* Auto EOM Latch Reset */ |
|---|
| 228 | #define AUTORTS 0x04 /* Auto RTS */ |
|---|
| 229 | #define TXDNRZI 0x08 /* TxD Pulled High in SDLC NRZI mode */ |
|---|
| 230 | #define RXFIFOH 0x08 /* Z85230: Int on RX FIFO half full */ |
|---|
| 231 | #define FASTDTR 0x10 /* Fast DTR/REQ Mode */ |
|---|
| 232 | #define CRCCBCR 0x20 /* CRC Check Bytes Completely Received */ |
|---|
| 233 | #define TXFIFOE 0x20 /* Z85230: Int on TX FIFO completely empty */ |
|---|
| 234 | #define EXTRDEN 0x40 /* Extended Read Enabled */ |
|---|
| 235 | |
|---|
| 236 | /* Write Register 15 (external/status interrupt control) */ |
|---|
| 237 | #define SHDLCE 1 /* SDLC/HDLC Enhancements Enable */ |
|---|
| 238 | #define FIFOE 4 /* FIFO Enable */ |
|---|
| 239 | |
|---|
| 240 | /* Read Register 6 (frame status FIFO) */ |
|---|
| 241 | #define BCLSB 0xff /* LSB of 14 bits count */ |
|---|
| 242 | |
|---|
| 243 | /* Read Register 7 (frame status FIFO) */ |
|---|
| 244 | #define BCMSB 0x3f /* MSB of 14 bits count */ |
|---|
| 245 | #define FDA 0x40 /* FIFO Data Available Status */ |
|---|
| 246 | #define FOS 0x80 /* FIFO Overflow Status */ |
|---|
| 247 | |
|---|
