1 | /* SPDX-License-Identifier: GPL-2.0 */ |
2 | #ifndef LINUX_SSB_REGS_H_ |
3 | #define LINUX_SSB_REGS_H_ |
4 | |
5 | |
6 | /* SiliconBackplane Address Map. |
7 | * All regions may not exist on all chips. |
8 | */ |
9 | #define SSB_SDRAM_BASE 0x00000000U /* Physical SDRAM */ |
10 | #define SSB_PCI_MEM 0x08000000U /* Host Mode sb2pcitranslation0 (64 MB) */ |
11 | #define SSB_PCI_CFG 0x0c000000U /* Host Mode sb2pcitranslation1 (64 MB) */ |
12 | #define SSB_SDRAM_SWAPPED 0x10000000U /* Byteswapped Physical SDRAM */ |
13 | #define SSB_ENUM_BASE 0x18000000U /* Enumeration space base */ |
14 | #define SSB_ENUM_LIMIT 0x18010000U /* Enumeration space limit */ |
15 | |
16 | #define SSB_FLASH2 0x1c000000U /* Flash Region 2 (region 1 shadowed here) */ |
17 | #define SSB_FLASH2_SZ 0x02000000U /* Size of Flash Region 2 */ |
18 | |
19 | #define SSB_EXTIF_BASE 0x1f000000U /* External Interface region base address */ |
20 | #define SSB_FLASH1 0x1fc00000U /* Flash Region 1 */ |
21 | #define SSB_FLASH1_SZ 0x00400000U /* Size of Flash Region 1 */ |
22 | |
23 | #define SSB_PCI_DMA 0x40000000U /* Client Mode sb2pcitranslation2 (1 GB) */ |
24 | #define SSB_PCI_DMA_SZ 0x40000000U /* Client Mode sb2pcitranslation2 size in bytes */ |
25 | #define SSB_PCIE_DMA_L32 0x00000000U /* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), low 32 bits */ |
26 | #define SSB_PCIE_DMA_H32 0x80000000U /* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), high 32 bits */ |
27 | #define SSB_EUART (SSB_EXTIF_BASE + 0x00800000) |
28 | #define SSB_LED (SSB_EXTIF_BASE + 0x00900000) |
29 | |
30 | |
31 | /* Enumeration space constants */ |
32 | #define SSB_CORE_SIZE 0x1000 /* Size of a core MMIO area */ |
33 | #define SSB_MAX_NR_CORES ((SSB_ENUM_LIMIT - SSB_ENUM_BASE) / SSB_CORE_SIZE) |
34 | |
35 | |
36 | /* mips address */ |
37 | #define SSB_EJTAG 0xff200000 /* MIPS EJTAG space (2M) */ |
38 | |
39 | |
40 | /* SSB PCI config space registers. */ |
41 | #define SSB_PMCSR 0x44 |
42 | #define SSB_PE 0x100 |
43 | #define SSB_BAR0_WIN 0x80 /* Backplane address space 0 */ |
44 | #define SSB_BAR1_WIN 0x84 /* Backplane address space 1 */ |
45 | #define SSB_SPROMCTL 0x88 /* SPROM control */ |
46 | #define SSB_SPROMCTL_WE 0x10 /* SPROM write enable */ |
47 | #define SSB_BAR1_CONTROL 0x8c /* Address space 1 burst control */ |
48 | #define SSB_PCI_IRQS 0x90 /* PCI interrupts */ |
49 | #define SSB_PCI_IRQMASK 0x94 /* PCI IRQ control and mask (pcirev >= 6 only) */ |
50 | #define SSB_BACKPLANE_IRQS 0x98 /* Backplane Interrupts */ |
51 | #define SSB_GPIO_IN 0xB0 /* GPIO Input (pcirev >= 3 only) */ |
52 | #define SSB_GPIO_OUT 0xB4 /* GPIO Output (pcirev >= 3 only) */ |
53 | #define SSB_GPIO_OUT_ENABLE 0xB8 /* GPIO Output Enable/Disable (pcirev >= 3 only) */ |
54 | #define SSB_GPIO_SCS 0x10 /* PCI config space bit 4 for 4306c0 slow clock source */ |
55 | #define SSB_GPIO_HWRAD 0x20 /* PCI config space GPIO 13 for hw radio disable */ |
56 | #define SSB_GPIO_XTAL 0x40 /* PCI config space GPIO 14 for Xtal powerup */ |
57 | #define SSB_GPIO_PLL 0x80 /* PCI config space GPIO 15 for PLL powerdown */ |
58 | |
59 | |
60 | #define SSB_BAR0_MAX_RETRIES 50 |
61 | |
62 | /* Silicon backplane configuration register definitions */ |
63 | #define SSB_IPSFLAG 0x0F08 |
64 | #define SSB_IPSFLAG_IRQ1 0x0000003F /* which sbflags get routed to mips interrupt 1 */ |
65 | #define SSB_IPSFLAG_IRQ1_SHIFT 0 |
66 | #define SSB_IPSFLAG_IRQ2 0x00003F00 /* which sbflags get routed to mips interrupt 2 */ |
67 | #define SSB_IPSFLAG_IRQ2_SHIFT 8 |
68 | #define SSB_IPSFLAG_IRQ3 0x003F0000 /* which sbflags get routed to mips interrupt 3 */ |
69 | #define SSB_IPSFLAG_IRQ3_SHIFT 16 |
70 | #define SSB_IPSFLAG_IRQ4 0x3F000000 /* which sbflags get routed to mips interrupt 4 */ |
71 | #define SSB_IPSFLAG_IRQ4_SHIFT 24 |
72 | #define SSB_TPSFLAG 0x0F18 |
73 | #define SSB_TPSFLAG_BPFLAG 0x0000003F /* Backplane flag # */ |
74 | #define SSB_TPSFLAG_ALWAYSIRQ 0x00000040 /* IRQ is always sent on the Backplane */ |
75 | #define SSB_TMERRLOGA 0x0F48 |
76 | #define SSB_TMERRLOG 0x0F50 |
77 | #define SSB_ADMATCH3 0x0F60 |
78 | #define SSB_ADMATCH2 0x0F68 |
79 | #define SSB_ADMATCH1 0x0F70 |
80 | #define SSB_IMSTATE 0x0F90 /* SB Initiator Agent State */ |
81 | #define SSB_IMSTATE_PC 0x0000000f /* Pipe Count */ |
82 | #define SSB_IMSTATE_AP_MASK 0x00000030 /* Arbitration Priority */ |
83 | #define SSB_IMSTATE_AP_BOTH 0x00000000 /* Use both timeslices and token */ |
84 | #define SSB_IMSTATE_AP_TS 0x00000010 /* Use timeslices only */ |
85 | #define SSB_IMSTATE_AP_TK 0x00000020 /* Use token only */ |
86 | #define SSB_IMSTATE_AP_RSV 0x00000030 /* Reserved */ |
87 | #define SSB_IMSTATE_IBE 0x00020000 /* In Band Error */ |
88 | #define SSB_IMSTATE_TO 0x00040000 /* Timeout */ |
89 | #define SSB_IMSTATE_BUSY 0x01800000 /* Busy (Backplane rev >= 2.3 only) */ |
90 | #define SSB_IMSTATE_REJECT 0x02000000 /* Reject (Backplane rev >= 2.3 only) */ |
91 | #define SSB_INTVEC 0x0F94 /* SB Interrupt Mask */ |
92 | #define SSB_INTVEC_PCI 0x00000001 /* Enable interrupts for PCI */ |
93 | #define SSB_INTVEC_ENET0 0x00000002 /* Enable interrupts for enet 0 */ |
94 | #define SSB_INTVEC_ILINE20 0x00000004 /* Enable interrupts for iline20 */ |
95 | #define SSB_INTVEC_CODEC 0x00000008 /* Enable interrupts for v90 codec */ |
96 | #define SSB_INTVEC_USB 0x00000010 /* Enable interrupts for usb */ |
97 | #define SSB_INTVEC_EXTIF 0x00000020 /* Enable interrupts for external i/f */ |
98 | #define SSB_INTVEC_ENET1 0x00000040 /* Enable interrupts for enet 1 */ |
99 | #define SSB_TMSLOW 0x0F98 /* SB Target State Low */ |
100 | #define SSB_TMSLOW_RESET 0x00000001 /* Reset */ |
101 | #define SSB_TMSLOW_REJECT 0x00000002 /* Reject (Standard Backplane) */ |
102 | #define SSB_TMSLOW_REJECT_23 0x00000004 /* Reject (Backplane rev 2.3) */ |
103 | #define SSB_TMSLOW_CLOCK 0x00010000 /* Clock Enable */ |
104 | #define SSB_TMSLOW_FGC 0x00020000 /* Force Gated Clocks On */ |
105 | #define SSB_TMSLOW_PE 0x40000000 /* Power Management Enable */ |
106 | #define SSB_TMSLOW_BE 0x80000000 /* BIST Enable */ |
107 | #define SSB_TMSHIGH 0x0F9C /* SB Target State High */ |
108 | #define SSB_TMSHIGH_SERR 0x00000001 /* S-error */ |
109 | #define SSB_TMSHIGH_INT 0x00000002 /* Interrupt */ |
110 | #define SSB_TMSHIGH_BUSY 0x00000004 /* Busy */ |
111 | #define SSB_TMSHIGH_TO 0x00000020 /* Timeout. Backplane rev >= 2.3 only */ |
112 | #define SSB_TMSHIGH_COREFL 0x1FFF0000 /* Core specific flags */ |
113 | #define SSB_TMSHIGH_COREFL_SHIFT 16 |
114 | #define SSB_TMSHIGH_DMA64 0x10000000 /* 64bit DMA supported */ |
115 | #define SSB_TMSHIGH_GCR 0x20000000 /* Gated Clock Request */ |
116 | #define SSB_TMSHIGH_BISTF 0x40000000 /* BIST Failed */ |
117 | #define SSB_TMSHIGH_BISTD 0x80000000 /* BIST Done */ |
118 | #define SSB_BWA0 0x0FA0 |
119 | #define SSB_IMCFGLO 0x0FA8 |
120 | #define SSB_IMCFGLO_SERTO 0x00000007 /* Service timeout */ |
121 | #define SSB_IMCFGLO_REQTO 0x00000070 /* Request timeout */ |
122 | #define SSB_IMCFGLO_REQTO_SHIFT 4 |
123 | #define SSB_IMCFGLO_CONNID 0x00FF0000 /* Connection ID */ |
124 | #define SSB_IMCFGLO_CONNID_SHIFT 16 |
125 | #define SSB_IMCFGHI 0x0FAC |
126 | #define SSB_ADMATCH0 0x0FB0 |
127 | #define SSB_TMCFGLO 0x0FB8 |
128 | #define SSB_TMCFGHI 0x0FBC |
129 | #define SSB_BCONFIG 0x0FC0 |
130 | #define SSB_BSTATE 0x0FC8 |
131 | #define SSB_ACTCFG 0x0FD8 |
132 | #define SSB_FLAGST 0x0FE8 |
133 | #define SSB_IDLOW 0x0FF8 |
134 | #define SSB_IDLOW_CFGSP 0x00000003 /* Config Space */ |
135 | #define SSB_IDLOW_ADDRNGE 0x00000038 /* Address Ranges supported */ |
136 | #define SSB_IDLOW_ADDRNGE_SHIFT 3 |
137 | #define SSB_IDLOW_SYNC 0x00000040 |
138 | #define SSB_IDLOW_INITIATOR 0x00000080 |
139 | #define SSB_IDLOW_MIBL 0x00000F00 /* Minimum Backplane latency */ |
140 | #define SSB_IDLOW_MIBL_SHIFT 8 |
141 | #define SSB_IDLOW_MABL 0x0000F000 /* Maximum Backplane latency */ |
142 | #define SSB_IDLOW_MABL_SHIFT 12 |
143 | #define SSB_IDLOW_TIF 0x00010000 /* This Initiator is first */ |
144 | #define SSB_IDLOW_CCW 0x000C0000 /* Cycle counter width */ |
145 | #define SSB_IDLOW_CCW_SHIFT 18 |
146 | #define SSB_IDLOW_TPT 0x00F00000 /* Target ports */ |
147 | #define SSB_IDLOW_TPT_SHIFT 20 |
148 | #define SSB_IDLOW_INITP 0x0F000000 /* Initiator ports */ |
149 | #define SSB_IDLOW_INITP_SHIFT 24 |
150 | #define SSB_IDLOW_SSBREV 0xF0000000 /* Sonics Backplane Revision code */ |
151 | #define SSB_IDLOW_SSBREV_22 0x00000000 /* <= 2.2 */ |
152 | #define SSB_IDLOW_SSBREV_23 0x10000000 /* 2.3 */ |
153 | #define SSB_IDLOW_SSBREV_24 0x40000000 /* ?? Found in BCM4328 */ |
154 | #define SSB_IDLOW_SSBREV_25 0x50000000 /* ?? Not Found yet */ |
155 | #define SSB_IDLOW_SSBREV_26 0x60000000 /* ?? Found in some BCM4311/2 */ |
156 | #define SSB_IDLOW_SSBREV_27 0x70000000 /* ?? Found in some BCM4311/2 */ |
157 | #define SSB_IDHIGH 0x0FFC /* SB Identification High */ |
158 | #define SSB_IDHIGH_RCLO 0x0000000F /* Revision Code (low part) */ |
159 | #define SSB_IDHIGH_CC 0x00008FF0 /* Core Code */ |
160 | #define SSB_IDHIGH_CC_SHIFT 4 |
161 | #define SSB_IDHIGH_RCHI 0x00007000 /* Revision Code (high part) */ |
162 | #define SSB_IDHIGH_RCHI_SHIFT 8 /* yes, shift 8 is right */ |
163 | #define SSB_IDHIGH_VC 0xFFFF0000 /* Vendor Code */ |
164 | #define SSB_IDHIGH_VC_SHIFT 16 |
165 | |
166 | /* SPROM shadow area. If not otherwise noted, fields are |
167 | * two bytes wide. Note that the SPROM can _only_ be read |
168 | * in two-byte quantities. |
169 | */ |
170 | #define SSB_SPROMSIZE_WORDS 64 |
171 | #define SSB_SPROMSIZE_BYTES (SSB_SPROMSIZE_WORDS * sizeof(u16)) |
172 | #define SSB_SPROMSIZE_WORDS_R123 64 |
173 | #define SSB_SPROMSIZE_WORDS_R4 220 |
174 | #define SSB_SPROMSIZE_BYTES_R123 (SSB_SPROMSIZE_WORDS_R123 * sizeof(u16)) |
175 | #define SSB_SPROMSIZE_BYTES_R4 (SSB_SPROMSIZE_WORDS_R4 * sizeof(u16)) |
176 | #define SSB_SPROMSIZE_WORDS_R10 230 |
177 | #define SSB_SPROMSIZE_WORDS_R11 234 |
178 | #define SSB_SPROM_BASE1 0x1000 |
179 | #define SSB_SPROM_BASE31 0x0800 |
180 | #define SSB_SPROM_REVISION 0x007E |
181 | #define SSB_SPROM_REVISION_REV 0x00FF /* SPROM Revision number */ |
182 | #define SSB_SPROM_REVISION_CRC 0xFF00 /* SPROM CRC8 value */ |
183 | #define SSB_SPROM_REVISION_CRC_SHIFT 8 |
184 | |
185 | /* SPROM Revision 1 */ |
186 | #define SSB_SPROM1_SPID 0x0004 /* Subsystem Product ID for PCI */ |
187 | #define SSB_SPROM1_SVID 0x0006 /* Subsystem Vendor ID for PCI */ |
188 | #define SSB_SPROM1_PID 0x0008 /* Product ID for PCI */ |
189 | #define SSB_SPROM1_IL0MAC 0x0048 /* 6 bytes MAC address for 802.11b/g */ |
190 | #define SSB_SPROM1_ET0MAC 0x004E /* 6 bytes MAC address for Ethernet */ |
191 | #define SSB_SPROM1_ET1MAC 0x0054 /* 6 bytes MAC address for 802.11a */ |
192 | #define SSB_SPROM1_ETHPHY 0x005A /* Ethernet PHY settings */ |
193 | #define SSB_SPROM1_ETHPHY_ET0A 0x001F /* MII Address for enet0 */ |
194 | #define SSB_SPROM1_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */ |
195 | #define SSB_SPROM1_ETHPHY_ET1A_SHIFT 5 |
196 | #define SSB_SPROM1_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */ |
197 | #define SSB_SPROM1_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */ |
198 | #define SSB_SPROM1_BINF 0x005C /* Board info */ |
199 | #define SSB_SPROM1_BINF_BREV 0x00FF /* Board Revision */ |
200 | #define SSB_SPROM1_BINF_CCODE 0x0F00 /* Country Code */ |
201 | #define SSB_SPROM1_BINF_CCODE_SHIFT 8 |
202 | #define SSB_SPROM1_BINF_ANTBG 0x3000 /* Available B-PHY and G-PHY antennas */ |
203 | #define SSB_SPROM1_BINF_ANTBG_SHIFT 12 |
204 | #define SSB_SPROM1_BINF_ANTA 0xC000 /* Available A-PHY antennas */ |
205 | #define SSB_SPROM1_BINF_ANTA_SHIFT 14 |
206 | #define SSB_SPROM1_PA0B0 0x005E |
207 | #define SSB_SPROM1_PA0B1 0x0060 |
208 | #define SSB_SPROM1_PA0B2 0x0062 |
209 | #define SSB_SPROM1_GPIOA 0x0064 /* General Purpose IO pins 0 and 1 */ |
210 | #define SSB_SPROM1_GPIOA_P0 0x00FF /* Pin 0 */ |
211 | #define SSB_SPROM1_GPIOA_P1 0xFF00 /* Pin 1 */ |
212 | #define SSB_SPROM1_GPIOA_P1_SHIFT 8 |
213 | #define SSB_SPROM1_GPIOB 0x0066 /* General Purpuse IO pins 2 and 3 */ |
214 | #define SSB_SPROM1_GPIOB_P2 0x00FF /* Pin 2 */ |
215 | #define SSB_SPROM1_GPIOB_P3 0xFF00 /* Pin 3 */ |
216 | #define SSB_SPROM1_GPIOB_P3_SHIFT 8 |
217 | #define SSB_SPROM1_MAXPWR 0x0068 /* Power Amplifier Max Power */ |
218 | #define SSB_SPROM1_MAXPWR_BG 0x00FF /* B-PHY and G-PHY (in dBm Q5.2) */ |
219 | #define SSB_SPROM1_MAXPWR_A 0xFF00 /* A-PHY (in dBm Q5.2) */ |
220 | #define SSB_SPROM1_MAXPWR_A_SHIFT 8 |
221 | #define SSB_SPROM1_PA1B0 0x006A |
222 | #define SSB_SPROM1_PA1B1 0x006C |
223 | #define SSB_SPROM1_PA1B2 0x006E |
224 | #define SSB_SPROM1_ITSSI 0x0070 /* Idle TSSI Target */ |
225 | #define SSB_SPROM1_ITSSI_BG 0x00FF /* B-PHY and G-PHY*/ |
226 | #define SSB_SPROM1_ITSSI_A 0xFF00 /* A-PHY */ |
227 | #define SSB_SPROM1_ITSSI_A_SHIFT 8 |
228 | #define SSB_SPROM1_BFLLO 0x0072 /* Boardflags (low 16 bits) */ |
229 | #define SSB_SPROM1_AGAIN 0x0074 /* Antenna Gain (in dBm Q5.2) */ |
230 | #define SSB_SPROM1_AGAIN_BG 0x00FF /* B-PHY and G-PHY */ |
231 | #define SSB_SPROM1_AGAIN_BG_SHIFT 0 |
232 | #define SSB_SPROM1_AGAIN_A 0xFF00 /* A-PHY */ |
233 | #define SSB_SPROM1_AGAIN_A_SHIFT 8 |
234 | #define SSB_SPROM1_CCODE 0x0076 |
235 | |
236 | /* SPROM Revision 2 (inherits from rev 1) */ |
237 | #define SSB_SPROM2_BFLHI 0x0038 /* Boardflags (high 16 bits) */ |
238 | #define SSB_SPROM2_MAXP_A 0x003A /* A-PHY Max Power */ |
239 | #define SSB_SPROM2_MAXP_A_HI 0x00FF /* Max Power High */ |
240 | #define SSB_SPROM2_MAXP_A_LO 0xFF00 /* Max Power Low */ |
241 | #define SSB_SPROM2_MAXP_A_LO_SHIFT 8 |
242 | #define SSB_SPROM2_PA1LOB0 0x003C /* A-PHY PowerAmplifier Low Settings */ |
243 | #define SSB_SPROM2_PA1LOB1 0x003E /* A-PHY PowerAmplifier Low Settings */ |
244 | #define SSB_SPROM2_PA1LOB2 0x0040 /* A-PHY PowerAmplifier Low Settings */ |
245 | #define SSB_SPROM2_PA1HIB0 0x0042 /* A-PHY PowerAmplifier High Settings */ |
246 | #define SSB_SPROM2_PA1HIB1 0x0044 /* A-PHY PowerAmplifier High Settings */ |
247 | #define SSB_SPROM2_PA1HIB2 0x0046 /* A-PHY PowerAmplifier High Settings */ |
248 | #define SSB_SPROM2_OPO 0x0078 /* OFDM Power Offset from CCK Level */ |
249 | #define SSB_SPROM2_OPO_VALUE 0x00FF |
250 | #define SSB_SPROM2_OPO_UNUSED 0xFF00 |
251 | #define SSB_SPROM2_CCODE 0x007C /* Two char Country Code */ |
252 | |
253 | /* SPROM Revision 3 (inherits most data from rev 2) */ |
254 | #define SSB_SPROM3_OFDMAPO 0x002C /* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */ |
255 | #define SSB_SPROM3_OFDMALPO 0x0030 /* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */ |
256 | #define SSB_SPROM3_OFDMAHPO 0x0034 /* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */ |
257 | #define SSB_SPROM3_GPIOLDC 0x0042 /* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */ |
258 | #define SSB_SPROM3_GPIOLDC_OFF 0x0000FF00 /* Off Count */ |
259 | #define SSB_SPROM3_GPIOLDC_OFF_SHIFT 8 |
260 | #define SSB_SPROM3_GPIOLDC_ON 0x00FF0000 /* On Count */ |
261 | #define SSB_SPROM3_GPIOLDC_ON_SHIFT 16 |
262 | #define SSB_SPROM3_IL0MAC 0x004A /* 6 bytes MAC address for 802.11b/g */ |
263 | #define SSB_SPROM3_CCKPO 0x0078 /* CCK Power Offset */ |
264 | #define SSB_SPROM3_CCKPO_1M 0x000F /* 1M Rate PO */ |
265 | #define SSB_SPROM3_CCKPO_2M 0x00F0 /* 2M Rate PO */ |
266 | #define SSB_SPROM3_CCKPO_2M_SHIFT 4 |
267 | #define SSB_SPROM3_CCKPO_55M 0x0F00 /* 5.5M Rate PO */ |
268 | #define SSB_SPROM3_CCKPO_55M_SHIFT 8 |
269 | #define SSB_SPROM3_CCKPO_11M 0xF000 /* 11M Rate PO */ |
270 | #define SSB_SPROM3_CCKPO_11M_SHIFT 12 |
271 | #define SSB_SPROM3_OFDMGPO 0x107A /* G-PHY OFDM Power Offset (4 bytes, BigEndian) */ |
272 | |
273 | /* SPROM Revision 4 */ |
274 | #define SSB_SPROM4_BOARDREV 0x0042 /* Board revision */ |
275 | #define SSB_SPROM4_BFLLO 0x0044 /* Boardflags (low 16 bits) */ |
276 | #define SSB_SPROM4_BFLHI 0x0046 /* Board Flags Hi */ |
277 | #define SSB_SPROM4_BFL2LO 0x0048 /* Board flags 2 (low 16 bits) */ |
278 | #define SSB_SPROM4_BFL2HI 0x004A /* Board flags 2 Hi */ |
279 | #define SSB_SPROM4_IL0MAC 0x004C /* 6 byte MAC address for a/b/g/n */ |
280 | #define SSB_SPROM4_CCODE 0x0052 /* Country Code (2 bytes) */ |
281 | #define SSB_SPROM4_GPIOA 0x0056 /* Gen. Purpose IO # 0 and 1 */ |
282 | #define SSB_SPROM4_GPIOA_P0 0x00FF /* Pin 0 */ |
283 | #define SSB_SPROM4_GPIOA_P1 0xFF00 /* Pin 1 */ |
284 | #define SSB_SPROM4_GPIOA_P1_SHIFT 8 |
285 | #define SSB_SPROM4_GPIOB 0x0058 /* Gen. Purpose IO # 2 and 3 */ |
286 | #define SSB_SPROM4_GPIOB_P2 0x00FF /* Pin 2 */ |
287 | #define SSB_SPROM4_GPIOB_P3 0xFF00 /* Pin 3 */ |
288 | #define SSB_SPROM4_GPIOB_P3_SHIFT 8 |
289 | #define SSB_SPROM4_ETHPHY 0x005A /* Ethernet PHY settings ?? */ |
290 | #define SSB_SPROM4_ETHPHY_ET0A 0x001F /* MII Address for enet0 */ |
291 | #define SSB_SPROM4_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */ |
292 | #define SSB_SPROM4_ETHPHY_ET1A_SHIFT 5 |
293 | #define SSB_SPROM4_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */ |
294 | #define SSB_SPROM4_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */ |
295 | #define SSB_SPROM4_ANTAVAIL 0x005C /* Antenna available bitfields */ |
296 | #define SSB_SPROM4_ANTAVAIL_BG 0x00FF /* B-PHY and G-PHY bitfield */ |
297 | #define SSB_SPROM4_ANTAVAIL_BG_SHIFT 0 |
298 | #define SSB_SPROM4_ANTAVAIL_A 0xFF00 /* A-PHY bitfield */ |
299 | #define SSB_SPROM4_ANTAVAIL_A_SHIFT 8 |
300 | #define SSB_SPROM4_AGAIN01 0x005E /* Antenna Gain (in dBm Q5.2) */ |
301 | #define SSB_SPROM4_AGAIN0 0x00FF /* Antenna 0 */ |
302 | #define SSB_SPROM4_AGAIN0_SHIFT 0 |
303 | #define SSB_SPROM4_AGAIN1 0xFF00 /* Antenna 1 */ |
304 | #define SSB_SPROM4_AGAIN1_SHIFT 8 |
305 | #define SSB_SPROM4_AGAIN23 0x0060 |
306 | #define SSB_SPROM4_AGAIN2 0x00FF /* Antenna 2 */ |
307 | #define SSB_SPROM4_AGAIN2_SHIFT 0 |
308 | #define SSB_SPROM4_AGAIN3 0xFF00 /* Antenna 3 */ |
309 | #define SSB_SPROM4_AGAIN3_SHIFT 8 |
310 | #define SSB_SPROM4_TXPID2G01 0x0062 /* TX Power Index 2GHz */ |
311 | #define SSB_SPROM4_TXPID2G0 0x00FF |
312 | #define SSB_SPROM4_TXPID2G0_SHIFT 0 |
313 | #define SSB_SPROM4_TXPID2G1 0xFF00 |
314 | #define SSB_SPROM4_TXPID2G1_SHIFT 8 |
315 | #define SSB_SPROM4_TXPID2G23 0x0064 /* TX Power Index 2GHz */ |
316 | #define SSB_SPROM4_TXPID2G2 0x00FF |
317 | #define SSB_SPROM4_TXPID2G2_SHIFT 0 |
318 | #define SSB_SPROM4_TXPID2G3 0xFF00 |
319 | #define SSB_SPROM4_TXPID2G3_SHIFT 8 |
320 | #define SSB_SPROM4_TXPID5G01 0x0066 /* TX Power Index 5GHz middle subband */ |
321 | #define SSB_SPROM4_TXPID5G0 0x00FF |
322 | #define SSB_SPROM4_TXPID5G0_SHIFT 0 |
323 | #define SSB_SPROM4_TXPID5G1 0xFF00 |
324 | #define SSB_SPROM4_TXPID5G1_SHIFT 8 |
325 | #define SSB_SPROM4_TXPID5G23 0x0068 /* TX Power Index 5GHz middle subband */ |
326 | #define SSB_SPROM4_TXPID5G2 0x00FF |
327 | #define SSB_SPROM4_TXPID5G2_SHIFT 0 |
328 | #define SSB_SPROM4_TXPID5G3 0xFF00 |
329 | #define SSB_SPROM4_TXPID5G3_SHIFT 8 |
330 | #define SSB_SPROM4_TXPID5GL01 0x006A /* TX Power Index 5GHz low subband */ |
331 | #define SSB_SPROM4_TXPID5GL0 0x00FF |
332 | #define SSB_SPROM4_TXPID5GL0_SHIFT 0 |
333 | #define SSB_SPROM4_TXPID5GL1 0xFF00 |
334 | #define SSB_SPROM4_TXPID5GL1_SHIFT 8 |
335 | #define SSB_SPROM4_TXPID5GL23 0x006C /* TX Power Index 5GHz low subband */ |
336 | #define SSB_SPROM4_TXPID5GL2 0x00FF |
337 | #define SSB_SPROM4_TXPID5GL2_SHIFT 0 |
338 | #define SSB_SPROM4_TXPID5GL3 0xFF00 |
339 | #define SSB_SPROM4_TXPID5GL3_SHIFT 8 |
340 | #define SSB_SPROM4_TXPID5GH01 0x006E /* TX Power Index 5GHz high subband */ |
341 | #define SSB_SPROM4_TXPID5GH0 0x00FF |
342 | #define SSB_SPROM4_TXPID5GH0_SHIFT 0 |
343 | #define SSB_SPROM4_TXPID5GH1 0xFF00 |
344 | #define SSB_SPROM4_TXPID5GH1_SHIFT 8 |
345 | #define SSB_SPROM4_TXPID5GH23 0x0070 /* TX Power Index 5GHz high subband */ |
346 | #define SSB_SPROM4_TXPID5GH2 0x00FF |
347 | #define SSB_SPROM4_TXPID5GH2_SHIFT 0 |
348 | #define SSB_SPROM4_TXPID5GH3 0xFF00 |
349 | #define SSB_SPROM4_TXPID5GH3_SHIFT 8 |
350 | |
351 | /* There are 4 blocks with power info sharing the same layout */ |
352 | #define SSB_SPROM4_PWR_INFO_CORE0 0x0080 |
353 | #define SSB_SPROM4_PWR_INFO_CORE1 0x00AE |
354 | #define SSB_SPROM4_PWR_INFO_CORE2 0x00DC |
355 | #define SSB_SPROM4_PWR_INFO_CORE3 0x010A |
356 | |
357 | #define SSB_SPROM4_2G_MAXP_ITSSI 0x00 /* 2 GHz ITSSI and 2 GHz Max Power */ |
358 | #define SSB_SPROM4_2G_MAXP 0x00FF |
359 | #define SSB_SPROM4_2G_ITSSI 0xFF00 |
360 | #define SSB_SPROM4_2G_ITSSI_SHIFT 8 |
361 | #define SSB_SPROM4_2G_PA_0 0x02 /* 2 GHz power amp */ |
362 | #define SSB_SPROM4_2G_PA_1 0x04 |
363 | #define SSB_SPROM4_2G_PA_2 0x06 |
364 | #define SSB_SPROM4_2G_PA_3 0x08 |
365 | #define SSB_SPROM4_5G_MAXP_ITSSI 0x0A /* 5 GHz ITSSI and 5.3 GHz Max Power */ |
366 | #define SSB_SPROM4_5G_MAXP 0x00FF |
367 | #define SSB_SPROM4_5G_ITSSI 0xFF00 |
368 | #define SSB_SPROM4_5G_ITSSI_SHIFT 8 |
369 | #define SSB_SPROM4_5GHL_MAXP 0x0C /* 5.2 GHz and 5.8 GHz Max Power */ |
370 | #define SSB_SPROM4_5GH_MAXP 0x00FF |
371 | #define SSB_SPROM4_5GL_MAXP 0xFF00 |
372 | #define SSB_SPROM4_5GL_MAXP_SHIFT 8 |
373 | #define SSB_SPROM4_5G_PA_0 0x0E /* 5.3 GHz power amp */ |
374 | #define SSB_SPROM4_5G_PA_1 0x10 |
375 | #define SSB_SPROM4_5G_PA_2 0x12 |
376 | #define SSB_SPROM4_5G_PA_3 0x14 |
377 | #define SSB_SPROM4_5GL_PA_0 0x16 /* 5.2 GHz power amp */ |
378 | #define SSB_SPROM4_5GL_PA_1 0x18 |
379 | #define SSB_SPROM4_5GL_PA_2 0x1A |
380 | #define SSB_SPROM4_5GL_PA_3 0x1C |
381 | #define SSB_SPROM4_5GH_PA_0 0x1E /* 5.8 GHz power amp */ |
382 | #define SSB_SPROM4_5GH_PA_1 0x20 |
383 | #define SSB_SPROM4_5GH_PA_2 0x22 |
384 | #define SSB_SPROM4_5GH_PA_3 0x24 |
385 | |
386 | /* TODO: Make it deprecated */ |
387 | #define SSB_SPROM4_MAXP_BG 0x0080 /* Max Power BG in path 1 */ |
388 | #define SSB_SPROM4_MAXP_BG_MASK 0x00FF /* Mask for Max Power BG */ |
389 | #define SSB_SPROM4_ITSSI_BG 0xFF00 /* Mask for path 1 itssi_bg */ |
390 | #define SSB_SPROM4_ITSSI_BG_SHIFT 8 |
391 | #define SSB_SPROM4_MAXP_A 0x008A /* Max Power A in path 1 */ |
392 | #define SSB_SPROM4_MAXP_A_MASK 0x00FF /* Mask for Max Power A */ |
393 | #define SSB_SPROM4_ITSSI_A 0xFF00 /* Mask for path 1 itssi_a */ |
394 | #define SSB_SPROM4_ITSSI_A_SHIFT 8 |
395 | #define SSB_SPROM4_PA0B0 0x0082 /* The paXbY locations are */ |
396 | #define SSB_SPROM4_PA0B1 0x0084 /* only guesses */ |
397 | #define SSB_SPROM4_PA0B2 0x0086 |
398 | #define SSB_SPROM4_PA1B0 0x008E |
399 | #define SSB_SPROM4_PA1B1 0x0090 |
400 | #define SSB_SPROM4_PA1B2 0x0092 |
401 | |
402 | /* SPROM Revision 5 (inherits most data from rev 4) */ |
403 | #define SSB_SPROM5_CCODE 0x0044 /* Country Code (2 bytes) */ |
404 | #define SSB_SPROM5_BFLLO 0x004A /* Boardflags (low 16 bits) */ |
405 | #define SSB_SPROM5_BFLHI 0x004C /* Board Flags Hi */ |
406 | #define SSB_SPROM5_BFL2LO 0x004E /* Board flags 2 (low 16 bits) */ |
407 | #define SSB_SPROM5_BFL2HI 0x0050 /* Board flags 2 Hi */ |
408 | #define SSB_SPROM5_IL0MAC 0x0052 /* 6 byte MAC address for a/b/g/n */ |
409 | #define SSB_SPROM5_GPIOA 0x0076 /* Gen. Purpose IO # 0 and 1 */ |
410 | #define SSB_SPROM5_GPIOA_P0 0x00FF /* Pin 0 */ |
411 | #define SSB_SPROM5_GPIOA_P1 0xFF00 /* Pin 1 */ |
412 | #define SSB_SPROM5_GPIOA_P1_SHIFT 8 |
413 | #define SSB_SPROM5_GPIOB 0x0078 /* Gen. Purpose IO # 2 and 3 */ |
414 | #define SSB_SPROM5_GPIOB_P2 0x00FF /* Pin 2 */ |
415 | #define SSB_SPROM5_GPIOB_P3 0xFF00 /* Pin 3 */ |
416 | #define SSB_SPROM5_GPIOB_P3_SHIFT 8 |
417 | |
418 | /* SPROM Revision 8 */ |
419 | #define SSB_SPROM8_BOARDREV 0x0082 /* Board revision */ |
420 | #define SSB_SPROM8_BFLLO 0x0084 /* Board flags (bits 0-15) */ |
421 | #define SSB_SPROM8_BFLHI 0x0086 /* Board flags (bits 16-31) */ |
422 | #define SSB_SPROM8_BFL2LO 0x0088 /* Board flags (bits 32-47) */ |
423 | #define SSB_SPROM8_BFL2HI 0x008A /* Board flags (bits 48-63) */ |
424 | #define SSB_SPROM8_IL0MAC 0x008C /* 6 byte MAC address */ |
425 | #define SSB_SPROM8_CCODE 0x0092 /* 2 byte country code */ |
426 | #define SSB_SPROM8_GPIOA 0x0096 /*Gen. Purpose IO # 0 and 1 */ |
427 | #define SSB_SPROM8_GPIOA_P0 0x00FF /* Pin 0 */ |
428 | #define SSB_SPROM8_GPIOA_P1 0xFF00 /* Pin 1 */ |
429 | #define SSB_SPROM8_GPIOA_P1_SHIFT 8 |
430 | #define SSB_SPROM8_GPIOB 0x0098 /* Gen. Purpose IO # 2 and 3 */ |
431 | #define SSB_SPROM8_GPIOB_P2 0x00FF /* Pin 2 */ |
432 | #define SSB_SPROM8_GPIOB_P3 0xFF00 /* Pin 3 */ |
433 | #define SSB_SPROM8_GPIOB_P3_SHIFT 8 |
434 | #define SSB_SPROM8_LEDDC 0x009A |
435 | #define SSB_SPROM8_LEDDC_ON 0xFF00 /* oncount */ |
436 | #define SSB_SPROM8_LEDDC_ON_SHIFT 8 |
437 | #define SSB_SPROM8_LEDDC_OFF 0x00FF /* offcount */ |
438 | #define SSB_SPROM8_LEDDC_OFF_SHIFT 0 |
439 | #define SSB_SPROM8_ANTAVAIL 0x009C /* Antenna available bitfields*/ |
440 | #define SSB_SPROM8_ANTAVAIL_A 0xFF00 /* A-PHY bitfield */ |
441 | #define SSB_SPROM8_ANTAVAIL_A_SHIFT 8 |
442 | #define SSB_SPROM8_ANTAVAIL_BG 0x00FF /* B-PHY and G-PHY bitfield */ |
443 | #define SSB_SPROM8_ANTAVAIL_BG_SHIFT 0 |
444 | #define SSB_SPROM8_AGAIN01 0x009E /* Antenna Gain (in dBm Q5.2) */ |
445 | #define SSB_SPROM8_AGAIN0 0x00FF /* Antenna 0 */ |
446 | #define SSB_SPROM8_AGAIN0_SHIFT 0 |
447 | #define SSB_SPROM8_AGAIN1 0xFF00 /* Antenna 1 */ |
448 | #define SSB_SPROM8_AGAIN1_SHIFT 8 |
449 | #define SSB_SPROM8_AGAIN23 0x00A0 |
450 | #define SSB_SPROM8_AGAIN2 0x00FF /* Antenna 2 */ |
451 | #define SSB_SPROM8_AGAIN2_SHIFT 0 |
452 | #define SSB_SPROM8_AGAIN3 0xFF00 /* Antenna 3 */ |
453 | #define SSB_SPROM8_AGAIN3_SHIFT 8 |
454 | #define SSB_SPROM8_TXRXC 0x00A2 |
455 | #define SSB_SPROM8_TXRXC_TXCHAIN 0x000f |
456 | #define SSB_SPROM8_TXRXC_TXCHAIN_SHIFT 0 |
457 | #define SSB_SPROM8_TXRXC_RXCHAIN 0x00f0 |
458 | #define SSB_SPROM8_TXRXC_RXCHAIN_SHIFT 4 |
459 | #define SSB_SPROM8_TXRXC_SWITCH 0xff00 |
460 | #define SSB_SPROM8_TXRXC_SWITCH_SHIFT 8 |
461 | #define 0x00A4 /* RSSI params for 2GHz */ |
462 | #define 0x000F |
463 | #define 0x00F0 |
464 | #define 4 |
465 | #define 0x0700 |
466 | #define 8 |
467 | #define SSB_SPROM8_BXA2G 0x1800 |
468 | #define SSB_SPROM8_BXA2G_SHIFT 11 |
469 | #define 0x00A6 /* RSSI params for 5GHz */ |
470 | #define 0x000F |
471 | #define 0x00F0 |
472 | #define 4 |
473 | #define 0x0700 |
474 | #define 8 |
475 | #define SSB_SPROM8_BXA5G 0x1800 |
476 | #define SSB_SPROM8_BXA5G_SHIFT 11 |
477 | #define SSB_SPROM8_TRI25G 0x00A8 /* TX isolation 2.4&5.3GHz */ |
478 | #define SSB_SPROM8_TRI2G 0x00FF /* TX isolation 2.4GHz */ |
479 | #define SSB_SPROM8_TRI5G 0xFF00 /* TX isolation 5.3GHz */ |
480 | #define SSB_SPROM8_TRI5G_SHIFT 8 |
481 | #define SSB_SPROM8_TRI5GHL 0x00AA /* TX isolation 5.2/5.8GHz */ |
482 | #define SSB_SPROM8_TRI5GL 0x00FF /* TX isolation 5.2GHz */ |
483 | #define SSB_SPROM8_TRI5GH 0xFF00 /* TX isolation 5.8GHz */ |
484 | #define SSB_SPROM8_TRI5GH_SHIFT 8 |
485 | #define SSB_SPROM8_RXPO 0x00AC /* RX power offsets */ |
486 | #define SSB_SPROM8_RXPO2G 0x00FF /* 2GHz RX power offset */ |
487 | #define SSB_SPROM8_RXPO2G_SHIFT 0 |
488 | #define SSB_SPROM8_RXPO5G 0xFF00 /* 5GHz RX power offset */ |
489 | #define SSB_SPROM8_RXPO5G_SHIFT 8 |
490 | #define SSB_SPROM8_FEM2G 0x00AE |
491 | #define SSB_SPROM8_FEM5G 0x00B0 |
492 | #define SSB_SROM8_FEM_TSSIPOS 0x0001 |
493 | #define SSB_SROM8_FEM_TSSIPOS_SHIFT 0 |
494 | #define SSB_SROM8_FEM_EXTPA_GAIN 0x0006 |
495 | #define SSB_SROM8_FEM_EXTPA_GAIN_SHIFT 1 |
496 | #define SSB_SROM8_FEM_PDET_RANGE 0x00F8 |
497 | #define SSB_SROM8_FEM_PDET_RANGE_SHIFT 3 |
498 | #define SSB_SROM8_FEM_TR_ISO 0x0700 |
499 | #define SSB_SROM8_FEM_TR_ISO_SHIFT 8 |
500 | #define SSB_SROM8_FEM_ANTSWLUT 0xF800 |
501 | #define SSB_SROM8_FEM_ANTSWLUT_SHIFT 11 |
502 | #define SSB_SPROM8_THERMAL 0x00B2 |
503 | #define SSB_SPROM8_THERMAL_OFFSET 0x00ff |
504 | #define SSB_SPROM8_THERMAL_OFFSET_SHIFT 0 |
505 | #define SSB_SPROM8_THERMAL_TRESH 0xff00 |
506 | #define SSB_SPROM8_THERMAL_TRESH_SHIFT 8 |
507 | /* Temp sense related entries */ |
508 | #define SSB_SPROM8_RAWTS 0x00B4 |
509 | #define SSB_SPROM8_RAWTS_RAWTEMP 0x01ff |
510 | #define SSB_SPROM8_RAWTS_RAWTEMP_SHIFT 0 |
511 | #define SSB_SPROM8_RAWTS_MEASPOWER 0xfe00 |
512 | #define SSB_SPROM8_RAWTS_MEASPOWER_SHIFT 9 |
513 | #define SSB_SPROM8_OPT_CORRX 0x00B6 |
514 | #define SSB_SPROM8_OPT_CORRX_TEMP_SLOPE 0x00ff |
515 | #define SSB_SPROM8_OPT_CORRX_TEMP_SLOPE_SHIFT 0 |
516 | #define SSB_SPROM8_OPT_CORRX_TEMPCORRX 0xfc00 |
517 | #define SSB_SPROM8_OPT_CORRX_TEMPCORRX_SHIFT 10 |
518 | #define SSB_SPROM8_OPT_CORRX_TEMP_OPTION 0x0300 |
519 | #define SSB_SPROM8_OPT_CORRX_TEMP_OPTION_SHIFT 8 |
520 | /* FOC: freiquency offset correction, HWIQ: H/W IOCAL enable, IQSWP: IQ CAL swap disable */ |
521 | #define SSB_SPROM8_HWIQ_IQSWP 0x00B8 |
522 | #define SSB_SPROM8_HWIQ_IQSWP_FREQ_CORR 0x000f |
523 | #define SSB_SPROM8_HWIQ_IQSWP_FREQ_CORR_SHIFT 0 |
524 | #define SSB_SPROM8_HWIQ_IQSWP_IQCAL_SWP 0x0010 |
525 | #define SSB_SPROM8_HWIQ_IQSWP_IQCAL_SWP_SHIFT 4 |
526 | #define SSB_SPROM8_HWIQ_IQSWP_HW_IQCAL 0x0020 |
527 | #define SSB_SPROM8_HWIQ_IQSWP_HW_IQCAL_SHIFT 5 |
528 | #define SSB_SPROM8_TEMPDELTA 0x00BC |
529 | #define SSB_SPROM8_TEMPDELTA_PHYCAL 0x00ff |
530 | #define SSB_SPROM8_TEMPDELTA_PHYCAL_SHIFT 0 |
531 | #define SSB_SPROM8_TEMPDELTA_PERIOD 0x0f00 |
532 | #define SSB_SPROM8_TEMPDELTA_PERIOD_SHIFT 8 |
533 | #define SSB_SPROM8_TEMPDELTA_HYSTERESIS 0xf000 |
534 | #define SSB_SPROM8_TEMPDELTA_HYSTERESIS_SHIFT 12 |
535 | |
536 | /* There are 4 blocks with power info sharing the same layout */ |
537 | #define SSB_SROM8_PWR_INFO_CORE0 0x00C0 |
538 | #define SSB_SROM8_PWR_INFO_CORE1 0x00E0 |
539 | #define SSB_SROM8_PWR_INFO_CORE2 0x0100 |
540 | #define SSB_SROM8_PWR_INFO_CORE3 0x0120 |
541 | |
542 | #define SSB_SROM8_2G_MAXP_ITSSI 0x00 |
543 | #define SSB_SPROM8_2G_MAXP 0x00FF |
544 | #define SSB_SPROM8_2G_ITSSI 0xFF00 |
545 | #define SSB_SPROM8_2G_ITSSI_SHIFT 8 |
546 | #define SSB_SROM8_2G_PA_0 0x02 /* 2GHz power amp settings */ |
547 | #define SSB_SROM8_2G_PA_1 0x04 |
548 | #define SSB_SROM8_2G_PA_2 0x06 |
549 | #define SSB_SROM8_5G_MAXP_ITSSI 0x08 /* 5GHz ITSSI and 5.3GHz Max Power */ |
550 | #define SSB_SPROM8_5G_MAXP 0x00FF |
551 | #define SSB_SPROM8_5G_ITSSI 0xFF00 |
552 | #define SSB_SPROM8_5G_ITSSI_SHIFT 8 |
553 | #define SSB_SPROM8_5GHL_MAXP 0x0A /* 5.2GHz and 5.8GHz Max Power */ |
554 | #define SSB_SPROM8_5GH_MAXP 0x00FF |
555 | #define SSB_SPROM8_5GL_MAXP 0xFF00 |
556 | #define SSB_SPROM8_5GL_MAXP_SHIFT 8 |
557 | #define SSB_SROM8_5G_PA_0 0x0C /* 5.3GHz power amp settings */ |
558 | #define SSB_SROM8_5G_PA_1 0x0E |
559 | #define SSB_SROM8_5G_PA_2 0x10 |
560 | #define SSB_SROM8_5GL_PA_0 0x12 /* 5.2GHz power amp settings */ |
561 | #define SSB_SROM8_5GL_PA_1 0x14 |
562 | #define SSB_SROM8_5GL_PA_2 0x16 |
563 | #define SSB_SROM8_5GH_PA_0 0x18 /* 5.8GHz power amp settings */ |
564 | #define SSB_SROM8_5GH_PA_1 0x1A |
565 | #define SSB_SROM8_5GH_PA_2 0x1C |
566 | |
567 | /* TODO: Make it deprecated */ |
568 | #define SSB_SPROM8_MAXP_BG 0x00C0 /* Max Power 2GHz in path 1 */ |
569 | #define SSB_SPROM8_MAXP_BG_MASK 0x00FF /* Mask for Max Power 2GHz */ |
570 | #define SSB_SPROM8_ITSSI_BG 0xFF00 /* Mask for path 1 itssi_bg */ |
571 | #define SSB_SPROM8_ITSSI_BG_SHIFT 8 |
572 | #define SSB_SPROM8_PA0B0 0x00C2 /* 2GHz power amp settings */ |
573 | #define SSB_SPROM8_PA0B1 0x00C4 |
574 | #define SSB_SPROM8_PA0B2 0x00C6 |
575 | #define SSB_SPROM8_MAXP_A 0x00C8 /* Max Power 5.3GHz */ |
576 | #define SSB_SPROM8_MAXP_A_MASK 0x00FF /* Mask for Max Power 5.3GHz */ |
577 | #define SSB_SPROM8_ITSSI_A 0xFF00 /* Mask for path 1 itssi_a */ |
578 | #define SSB_SPROM8_ITSSI_A_SHIFT 8 |
579 | #define SSB_SPROM8_MAXP_AHL 0x00CA /* Max Power 5.2/5.8GHz */ |
580 | #define SSB_SPROM8_MAXP_AH_MASK 0x00FF /* Mask for Max Power 5.8GHz */ |
581 | #define SSB_SPROM8_MAXP_AL_MASK 0xFF00 /* Mask for Max Power 5.2GHz */ |
582 | #define SSB_SPROM8_MAXP_AL_SHIFT 8 |
583 | #define SSB_SPROM8_PA1B0 0x00CC /* 5.3GHz power amp settings */ |
584 | #define SSB_SPROM8_PA1B1 0x00CE |
585 | #define SSB_SPROM8_PA1B2 0x00D0 |
586 | #define SSB_SPROM8_PA1LOB0 0x00D2 /* 5.2GHz power amp settings */ |
587 | #define SSB_SPROM8_PA1LOB1 0x00D4 |
588 | #define SSB_SPROM8_PA1LOB2 0x00D6 |
589 | #define SSB_SPROM8_PA1HIB0 0x00D8 /* 5.8GHz power amp settings */ |
590 | #define SSB_SPROM8_PA1HIB1 0x00DA |
591 | #define SSB_SPROM8_PA1HIB2 0x00DC |
592 | |
593 | #define SSB_SPROM8_CCK2GPO 0x0140 /* CCK power offset */ |
594 | #define SSB_SPROM8_OFDM2GPO 0x0142 /* 2.4GHz OFDM power offset */ |
595 | #define SSB_SPROM8_OFDM5GPO 0x0146 /* 5.3GHz OFDM power offset */ |
596 | #define SSB_SPROM8_OFDM5GLPO 0x014A /* 5.2GHz OFDM power offset */ |
597 | #define SSB_SPROM8_OFDM5GHPO 0x014E /* 5.8GHz OFDM power offset */ |
598 | |
599 | #define SSB_SPROM8_2G_MCSPO 0x0152 |
600 | #define SSB_SPROM8_5G_MCSPO 0x0162 |
601 | #define SSB_SPROM8_5GL_MCSPO 0x0172 |
602 | #define SSB_SPROM8_5GH_MCSPO 0x0182 |
603 | |
604 | #define SSB_SPROM8_CDDPO 0x0192 |
605 | #define SSB_SPROM8_STBCPO 0x0194 |
606 | #define SSB_SPROM8_BW40PO 0x0196 |
607 | #define SSB_SPROM8_BWDUPPO 0x0198 |
608 | |
609 | /* Values for boardflags_lo read from SPROM */ |
610 | #define SSB_BFL_BTCOEXIST 0x0001 /* implements Bluetooth coexistance */ |
611 | #define SSB_BFL_PACTRL 0x0002 /* GPIO 9 controlling the PA */ |
612 | #define SSB_BFL_AIRLINEMODE 0x0004 /* implements GPIO 13 radio disable indication */ |
613 | #define 0x0008 /* software calculates nrssi slope. */ |
614 | #define SSB_BFL_ENETSPI 0x0010 /* has ephy roboswitch spi */ |
615 | #define SSB_BFL_XTAL_NOSLOW 0x0020 /* no slow clock available */ |
616 | #define SSB_BFL_CCKHIPWR 0x0040 /* can do high power CCK transmission */ |
617 | #define SSB_BFL_ENETADM 0x0080 /* has ADMtek switch */ |
618 | #define SSB_BFL_ENETVLAN 0x0100 /* can do vlan */ |
619 | #define SSB_BFL_AFTERBURNER 0x0200 /* supports Afterburner mode */ |
620 | #define SSB_BFL_NOPCI 0x0400 /* board leaves PCI floating */ |
621 | #define SSB_BFL_FEM 0x0800 /* supports the Front End Module */ |
622 | #define SSB_BFL_EXTLNA 0x1000 /* has an external LNA */ |
623 | #define SSB_BFL_HGPA 0x2000 /* had high gain PA */ |
624 | #define SSB_BFL_BTCMOD 0x4000 /* BFL_BTCOEXIST is given in alternate GPIOs */ |
625 | #define SSB_BFL_ALTIQ 0x8000 /* alternate I/Q settings */ |
626 | |
627 | /* Values for boardflags_hi read from SPROM */ |
628 | #define SSB_BFH_NOPA 0x0001 /* has no PA */ |
629 | #define 0x0002 /* RSSI uses positive slope (not TSSI) */ |
630 | #define SSB_BFH_PAREF 0x0004 /* uses the PARef LDO */ |
631 | #define SSB_BFH_3TSWITCH 0x0008 /* uses a triple throw switch shared with bluetooth */ |
632 | #define SSB_BFH_PHASESHIFT 0x0010 /* can support phase shifter */ |
633 | #define SSB_BFH_BUCKBOOST 0x0020 /* has buck/booster */ |
634 | #define SSB_BFH_FEM_BT 0x0040 /* has FEM and switch to share antenna with bluetooth */ |
635 | |
636 | /* Values for boardflags2_lo read from SPROM */ |
637 | #define SSB_BFL2_RXBB_INT_REG_DIS 0x0001 /* external RX BB regulator present */ |
638 | #define SSB_BFL2_APLL_WAR 0x0002 /* alternative A-band PLL settings implemented */ |
639 | #define SSB_BFL2_TXPWRCTRL_EN 0x0004 /* permits enabling TX Power Control */ |
640 | #define SSB_BFL2_2X4_DIV 0x0008 /* 2x4 diversity switch */ |
641 | #define SSB_BFL2_5G_PWRGAIN 0x0010 /* supports 5G band power gain */ |
642 | #define SSB_BFL2_PCIEWAR_OVR 0x0020 /* overrides ASPM and Clkreq settings */ |
643 | #define SSB_BFL2_CAESERS_BRD 0x0040 /* is Caesers board (unused) */ |
644 | #define SSB_BFL2_BTC3WIRE 0x0080 /* used 3-wire bluetooth coexist */ |
645 | #define SSB_BFL2_SKWRKFEM_BRD 0x0100 /* 4321mcm93 uses Skyworks FEM */ |
646 | #define SSB_BFL2_SPUR_WAR 0x0200 /* has a workaround for clock-harmonic spurs */ |
647 | #define SSB_BFL2_GPLL_WAR 0x0400 /* altenative G-band PLL settings implemented */ |
648 | |
649 | /* Values for SSB_SPROM1_BINF_CCODE */ |
650 | enum { |
651 | SSB_SPROM1CCODE_WORLD = 0, |
652 | SSB_SPROM1CCODE_THAILAND, |
653 | SSB_SPROM1CCODE_ISRAEL, |
654 | SSB_SPROM1CCODE_JORDAN, |
655 | SSB_SPROM1CCODE_CHINA, |
656 | SSB_SPROM1CCODE_JAPAN, |
657 | SSB_SPROM1CCODE_USA_CANADA_ANZ, |
658 | SSB_SPROM1CCODE_EUROPE, |
659 | SSB_SPROM1CCODE_USA_LOW, |
660 | SSB_SPROM1CCODE_JAPAN_HIGH, |
661 | SSB_SPROM1CCODE_ALL, |
662 | SSB_SPROM1CCODE_NONE, |
663 | }; |
664 | |
665 | /* Address-Match values and masks (SSB_ADMATCHxxx) */ |
666 | #define SSB_ADM_TYPE 0x00000003 /* Address type */ |
667 | #define SSB_ADM_TYPE0 0 |
668 | #define SSB_ADM_TYPE1 1 |
669 | #define SSB_ADM_TYPE2 2 |
670 | #define SSB_ADM_AD64 0x00000004 |
671 | #define SSB_ADM_SZ0 0x000000F8 /* Type0 size */ |
672 | #define SSB_ADM_SZ0_SHIFT 3 |
673 | #define SSB_ADM_SZ1 0x000001F8 /* Type1 size */ |
674 | #define SSB_ADM_SZ1_SHIFT 3 |
675 | #define SSB_ADM_SZ2 0x000001F8 /* Type2 size */ |
676 | #define SSB_ADM_SZ2_SHIFT 3 |
677 | #define SSB_ADM_EN 0x00000400 /* Enable */ |
678 | #define SSB_ADM_NEG 0x00000800 /* Negative decode */ |
679 | #define SSB_ADM_BASE0 0xFFFFFF00 /* Type0 base address */ |
680 | #define SSB_ADM_BASE0_SHIFT 8 |
681 | #define SSB_ADM_BASE1 0xFFFFF000 /* Type1 base address for the core */ |
682 | #define SSB_ADM_BASE1_SHIFT 12 |
683 | #define SSB_ADM_BASE2 0xFFFF0000 /* Type2 base address for the core */ |
684 | #define SSB_ADM_BASE2_SHIFT 16 |
685 | |
686 | |
687 | #endif /* LINUX_SSB_REGS_H_ */ |
688 | |