1 | /* SPDX-License-Identifier: GPL-2.0-only */ |
2 | /* |
3 | * Microchip SAMA7 UDDR Controller and DDR3 PHY Controller registers offsets |
4 | * and bit definitions. |
5 | * |
6 | * Copyright (C) [2020] Microchip Technology Inc. and its subsidiaries |
7 | * |
8 | * Author: Claudu Beznea <claudiu.beznea@microchip.com> |
9 | */ |
10 | |
11 | #ifndef __SAMA7_DDR_H__ |
12 | #define __SAMA7_DDR_H__ |
13 | |
14 | /* DDR3PHY */ |
15 | #define DDR3PHY_PIR (0x04) /* DDR3PHY PHY Initialization Register */ |
16 | #define DDR3PHY_PIR_DLLBYP (1 << 17) /* DLL Bypass */ |
17 | #define DDR3PHY_PIR_ITMSRST (1 << 4) /* Interface Timing Module Soft Reset */ |
18 | #define DDR3PHY_PIR_DLLLOCK (1 << 2) /* DLL Lock */ |
19 | #define DDR3PHY_PIR_DLLSRST (1 << 1) /* DLL Soft Rest */ |
20 | #define DDR3PHY_PIR_INIT (1 << 0) /* Initialization Trigger */ |
21 | |
22 | #define DDR3PHY_PGCR (0x08) /* DDR3PHY PHY General Configuration Register */ |
23 | #define DDR3PHY_PGCR_CKDV1 (1 << 13) /* CK# Disable Value */ |
24 | #define DDR3PHY_PGCR_CKDV0 (1 << 12) /* CK Disable Value */ |
25 | |
26 | #define DDR3PHY_PGSR (0x0C) /* DDR3PHY PHY General Status Register */ |
27 | #define DDR3PHY_PGSR_IDONE (1 << 0) /* Initialization Done */ |
28 | |
29 | #define DDR3PHY_ACDLLCR (0x14) /* DDR3PHY AC DLL Control Register */ |
30 | #define DDR3PHY_ACDLLCR_DLLSRST (1 << 30) /* DLL Soft Reset */ |
31 | |
32 | #define DDR3PHY_ACIOCR (0x24) /* DDR3PHY AC I/O Configuration Register */ |
33 | #define DDR3PHY_ACIOCR_CSPDD_CS0 (1 << 18) /* CS#[0] Power Down Driver */ |
34 | #define DDR3PHY_ACIOCR_CKPDD_CK0 (1 << 8) /* CK[0] Power Down Driver */ |
35 | #define DDR3PHY_ACIORC_ACPDD (1 << 3) /* AC Power Down Driver */ |
36 | |
37 | #define DDR3PHY_DXCCR (0x28) /* DDR3PHY DATX8 Common Configuration Register */ |
38 | #define DDR3PHY_DXCCR_DXPDR (1 << 3) /* Data Power Down Receiver */ |
39 | |
40 | #define DDR3PHY_DSGCR (0x2C) /* DDR3PHY DDR System General Configuration Register */ |
41 | #define DDR3PHY_DSGCR_ODTPDD_ODT0 (1 << 20) /* ODT[0] Power Down Driver */ |
42 | |
43 | #define DDR3PHY_ZQ0SR0 (0x188) /* ZQ status register 0 */ |
44 | #define DDR3PHY_ZQ0SR0_PDO_OFF (0) /* Pull-down output impedance select offset */ |
45 | #define DDR3PHY_ZQ0SR0_PUO_OFF (5) /* Pull-up output impedance select offset */ |
46 | #define DDR3PHY_ZQ0SR0_PDODT_OFF (10) /* Pull-down on-die termination impedance select offset */ |
47 | #define DDR3PHY_ZQ0SRO_PUODT_OFF (15) /* Pull-up on-die termination impedance select offset */ |
48 | |
49 | #define DDR3PHY_DX0DLLCR (0x1CC) /* DDR3PHY DATX8 DLL Control Register */ |
50 | #define DDR3PHY_DX1DLLCR (0x20C) /* DDR3PHY DATX8 DLL Control Register */ |
51 | #define DDR3PHY_DXDLLCR_DLLDIS (1 << 31) /* DLL Disable */ |
52 | |
53 | /* UDDRC */ |
54 | #define UDDRC_STAT (0x04) /* UDDRC Operating Mode Status Register */ |
55 | #define UDDRC_STAT_SELFREF_TYPE_DIS (0x0 << 4) /* SDRAM is not in Self-refresh */ |
56 | #define UDDRC_STAT_SELFREF_TYPE_PHY (0x1 << 4) /* SDRAM is in Self-refresh, which was caused by PHY Master Request */ |
57 | #define UDDRC_STAT_SELFREF_TYPE_SW (0x2 << 4) /* SDRAM is in Self-refresh, which was not caused solely under Automatic Self-refresh control */ |
58 | #define UDDRC_STAT_SELFREF_TYPE_AUTO (0x3 << 4) /* SDRAM is in Self-refresh, which was caused by Automatic Self-refresh only */ |
59 | #define UDDRC_STAT_SELFREF_TYPE_MSK (0x3 << 4) /* Self-refresh type mask */ |
60 | #define UDDRC_STAT_OPMODE_INIT (0x0 << 0) /* Init */ |
61 | #define UDDRC_STAT_OPMODE_NORMAL (0x1 << 0) /* Normal */ |
62 | #define UDDRC_STAT_OPMODE_PWRDOWN (0x2 << 0) /* Power-down */ |
63 | #define UDDRC_STAT_OPMODE_SELF_REFRESH (0x3 << 0) /* Self-refresh */ |
64 | #define UDDRC_STAT_OPMODE_MSK (0x7 << 0) /* Operating mode mask */ |
65 | |
66 | #define UDDRC_PWRCTL (0x30) /* UDDRC Low Power Control Register */ |
67 | #define UDDRC_PWRCTL_SELFREF_EN (1 << 0) /* Automatic self-refresh */ |
68 | #define UDDRC_PWRCTL_SELFREF_SW (1 << 5) /* Software self-refresh */ |
69 | |
70 | #define UDDRC_DFIMISC (0x1B0) /* UDDRC DFI Miscellaneous Control Register */ |
71 | #define UDDRC_DFIMISC_DFI_INIT_COMPLETE_EN (1 << 0) /* PHY initialization complete enable signal */ |
72 | |
73 | #define UDDRC_SWCTRL (0x320) /* UDDRC Software Register Programming Control Enable */ |
74 | #define UDDRC_SWCTRL_SW_DONE (1 << 0) /* Enable quasi-dynamic register programming outside reset */ |
75 | |
76 | #define UDDRC_SWSTAT (0x324) /* UDDRC Software Register Programming Control Status */ |
77 | #define UDDRC_SWSTAT_SW_DONE_ACK (1 << 0) /* Register programming done */ |
78 | |
79 | #define UDDRC_PSTAT (0x3FC) /* UDDRC Port Status Register */ |
80 | #define UDDRC_PSTAT_ALL_PORTS (0x1F001F) /* Read + writes outstanding transactions on all ports */ |
81 | |
82 | #define UDDRC_PCTRL_0 (0x490) /* UDDRC Port 0 Control Register */ |
83 | #define UDDRC_PCTRL_1 (0x540) /* UDDRC Port 1 Control Register */ |
84 | #define UDDRC_PCTRL_2 (0x5F0) /* UDDRC Port 2 Control Register */ |
85 | #define UDDRC_PCTRL_3 (0x6A0) /* UDDRC Port 3 Control Register */ |
86 | #define UDDRC_PCTRL_4 (0x750) /* UDDRC Port 4 Control Register */ |
87 | |
88 | #endif /* __SAMA7_DDR_H__ */ |
89 | |